广义正交码索引调制系统的性能分析

摘 要：为了提高码索引调制（code index modulation，CIM）系统的传输效率，提出了一种具有更低复杂度的单输入单输出（single input single output，SISO）的广义正交码索引调制（generalized orthogonal code index modulation，GQCIM）系统。CIM 系统使用扩频码和星座符号传输信息，但只能激活两个扩频码索引和一个调制符号。而 GQCIM 系统以一种新颖的方式克服了只激活一个调制符号的限制，同时充分利用了调制符号的正交性，增加扩频码索引以传输更多的额外信息位，提高了系统的传输效率。此外，分析了GQCIM系统的理论性能，推导了误码率性能的上界。通过蒙特卡罗仿真验证了GQCIM系统的性能，对比发现GQCIM系统的理论和仿真性能一致。而且在相同的传输效率下，结果显示GQCIM系统的性能优于同样具有正交性的调制系统，如广义码索引调制（generalized code index modulation，GCIM）系统、CIM系统、码索引调制-正交空间调制（code index modulation aided quadrature spatial modulation，CIM-QSM）系统、码索引调制-正交空间调制（code index modulation aided spatial modulation，CIM-SM）系统、脉冲索引调制（pulse index modulation，PIM）系统。     

基于Abaqus的双裂纹不同间距对裂纹扩展速率的研究

扩展有限元法是近年经过大量运用的,在传统有限元的范围中求解不连续问题一种有效计算方法,它是基于单位分解的思想,在计算不连续问题时加入跳跃函数。以ABAQUS为平台,基于扩展有限元方法 (XFEM),以含双穿透型裂纹的有限宽板受横向拉伸载荷为力学模型,建立相应的裂纹尖端应力的有限元模型,研究焊接接头区域不同间距双裂纹相互作用对裂纹扩展速率的影响。结果表明:双裂纹间距的的大小并没有对裂纹的扩展速率产生影响。     

Study on ice-melting performance of gradient gas diffusion layer in proton exchange membrane fuel cell

In this study, a three-dimensional model was established using the lattice Boltzmann method (LBM) to study the internal ice melting process of the gas diffusion layer (GDL) of the proton exchange membrane fuel cell (PEMFC). The single-point second-order curved boundary condition was adopted. The effects of GDL carbon fiber number, growth slope of the number of carbon fibers and carbon fiber diameter on ice melting were studied. The results were revealed that the temperature in the middle and lower part of the gradient distribution GDL is significantly higher than that of the no-gradient GDL. With the increase of the growth slope of the number of carbon fiber, the temperature and melting rate gradually increase, and the position of the solid-liquid interface gradually decreases. The decrease in the number of carbon fibers has a similar effect as the increase in the growth slope of the number of carbon fibers. In addition, as the diameter of the carbon fiber increases, the position of the solid-liquid interface gradually decreases first and then increases.     

Effects of upholstery materials on the burning behavior of real‐scale residential upholstered furniture mock‐ups

Fire spread and growth on real‐scale four cushion mock‐ups of residential upholstered furniture (RUF) were investigated with the goal of identifying whether changes in five classes of materials (barrier, flexible polyurethane foam, polyester fiber wrap, upholstery fabric, and sewing thread), referred to as factors, resulted in statistically significant changes in burning behavior. A fractional factorial experimental design plus practical considerations yielded a test matrix with 20 material combinations. Experiments were repeated a minimum of two times. Measurements included fire spread rates derived from video recordings and heat release rates (HRRs). A total of 13 experimental parameters (3 based on the videos and 10 on the HRR results), referred to as responses, characterized the measurements. Statistical analyses based on Main Effects Plots (main effects) and Block Plots (main effects and factor interactions) were used. The results showed that three of the factors resulted in statistically significant effects on varying numbers of the 13 responses. The Barrier and Fabric factors had the strongest main effects with roughly comparable magnitudes. Foam was statistically significant for fewer of the responses and its overall strength was weaker than for Barrier and Fabric. No statistically significant main effects were identified for Wrap or Thread. Multiple two‐term interactions between factors were identified as being statistically significant. The Barrier*Fabric interaction resulted in the highest number of and strongest statistically significant effects. The existence of two‐term interactions means that it will be necessary to consider their effects in approaches designed to predict the burning behavior of RUF.     

Investigation on thermal conductivity and mechanical properties of Si3N4 ceramics via one-step sintering

High thermal conductivity Si₃N₄ ceramics were fabricated using a one-step method consisting of reaction-bonded Si₃N₄ (RBSN) and post-sintering. The influence of Si content on nitridation rate, β/(α+β) phase rate, thermal conductivity and mechanical properties was investigated in this work. It is of special interest to note that the thermal conductivity showed a tendency to increase first and then decrease with increasing Si content. This experimental result shows that the optimal thermal conductivity and fracture toughness were obtained to be 66 W (m K)^-1 and 12.0 MPa m^1/2, respectively. As a comparison, the nitridation rate and β/(α+β) phase rate in a static pressure nitriding system, i.e., 97% (MS10), 97% (MS15), 97% (MS20) and 8.3% (MS10), 8.3% (MS15), 8.9% (MS20), respectively, have obvious advantages over those in a flowing nitriding system, i.e., 91% (MS10), 91% (MS15), 93% (MS20) and 3.1% (MS10), 3.3% (MS15), 3.3% (MS20), respectively. Moreover, high lattice integrity of the β-Si₃N₄ phase was observed, which can effectively confine O atoms into the β-Si₃N₄ lattice using MgO as a sintering additive. This result indicates that one-step sintering can provide a new route to prepare Si₃N₄ ceramics with a good combination of thermal conductivity and mechanical properties.     

Influence of SiC microstructure on its corrosion behavior in molten FLiNaK salt

The influence of the microstructure on the corrosion rate of three monolithic SiC samples in FLiNaK salt at 900 °C for 250 h was studied. The SiC samples, labeled as SiC-1, SiC-2, and SiC-3, had corrosion rates of 0.137, 0.020, and 0.043 mg/cm²h, respectively. Compared with grain size and the presence of special grain boundaries (i.e., Σ3), the content of high-angle grain boundaries (HAGBs) appeared to have the strongest influence on the corrosion rate of SiC in FLiNaK salt, since the corrosion rate increased six times as the concentration of high-angle grain boundaries increased from 19 to 32% for SiC-2 and SiC-1, respectively. These results stress the importance of controlling the content of HAGBs during the production process of SiC.     

Crowding as an Agronomic Factor Determining the Development of Plants and the Productivity of Linseed (Linum usitatissimum L.)

ABSTRACT

Nine sowing densities of linseed were compared in a two-year experiment. Self-regulation of the density of a linseed stand resulted in a differentiated branching of the plants. The number of capsules on a linseed shoot, as well as seeds in the capsule, and the number of seeds from the shoot were highly varied from year to year, and there is even a stronger differentiation in the weight of 1000 seeds. Linear relationships were noted between the mass of seeds from the linseed plant and the number of capsules. The yield of linseed was affected by both factors. An increasing sowing rate reduced the seed yield from the shoot and the plant. At lower seeding rates, the lateral shoots contributed in the seeds yield of the plant to a higher degree compared to the main ones.     

机械合金化FeS/Cu复合材料的摩擦磨损性能

以FeS和CuSn8Ni1粉末为原料，利用机械合金化技术和粉末冶金技术制备了FeS/Cu复合材料，探讨了不同载荷情况下所制备的FeS/Cu复合材料的摩擦学性能及润滑膜与转移膜特征。结果表明：机械合金化提高了FeS与铜合金基体界面结合性能，进而提高了材料减摩耐磨性能；当载荷较小时，摩擦副表面接触不稳定，复合转移膜不连续，摩擦因数波动大；载荷较大时，复合转移膜易破损，材料的减摩耐磨性能变差；当载荷为150 N时，载荷适宜，材料表面软化，复合转移膜更加完整，摩擦因数较小。