Analysis of Temperature Effect in Quadruple Gate Nano-scale FinFET

Silicon - Quadruple gate FinFET is a promising candidate among other multi-gate MOS devices due to it’s better scalability and higher short channel effect suppression capability in advanced...     

Authenticity green coffee bean species and geographical origin using near-infrared spectroscopy combined with chemometrics

To prevent the adulteration of agricultural resources and provide a solution to enhance the green coffee bean supply chain, authentication using the near-infrared spectroscopy (NIRS) technique was investigated. Partial least square with discrimination analysis (PLS-DA) models combined with various preprocessing methods were built from NIR spectra of 153 Vietnamese green coffee samples. The model combined with the standard normal variate and the first order of derivative yielded excellent performance in predicting coffee species with the error cross-validation of 0.0261. PLS-DA model of mean centre and first-order derivative spectra also yielded good performance in verifying geographical indication of green coffee with the error of 0.0656. By contrast, the predicting abilities of post-harvest methods were poor. The overall results showed a high potential of the NIRS in online authentication practices.     

Effect of MoS2/PTFE coatings on performance of Si3N4/TiC ceramics in dry sliding against WC/Co

To enhance the tribological performance of Si₃N₄/TiC ceramics, MoS₂/PTFE composite coatings were deposited on the ceramic substrate through spraying method. The micrographs and basic properties of the MoS₂/PTFE coated samples were investigated. Dry sliding friction experiments against WC/Co ball were performed with the coated ceramics and traditional ones. These results showed that the composite coatings could significantly reduce the friction coefficient of ceramics, and protect the substrate from adhesion wear. The primary tribological mechanisms of the coated ceramics were abrasive wear, coating spalling and delamination, and the tribological property was transited from slight wear to serious wear with the increase of load because of the lower surface hardness and shear strength. The possible mechanisms for the effects of MoS₂/PTFE composite coatings on the friction performance of ceramics were discussed.     

Anaerobic co-digestion of food waste and FOG with sewage sludge – realising its potential in Ireland

The severe environmental pollution in many countries is caused by indiscriminate discharge of large quantities of food waste (FW), fat oil and grease (FOG) and sewage sludge (SS) to the environment. There are many possible treatment routes, but anaerobic digestion (AD) is now well accepted for treating several kinds of organic wastes. But AD of FW alone presents some operational challenges because of substrates and variability. Anaerobic co-digestion of two or more substrates is better than single substrate digestion. This can use a plant’s unused capacity, in line with the trend to renewable energy. Co-digestion technology, although well established in many European countries, is still in its infancy in Ireland. There are problems with different regulatory arrangements. They should be resolved. The paper reviews anaerobic co-digestion technology is reviewed, with special focus on possible application in Ireland.     

Polyethylene oxide-polypropylene oxide -polyethylene oxide derived porous carbon materials with different molecular weights as ORR catalyst in alkaline electrolytes

Polyethylene oxide (PEO)-polypropylene oxide (PPO)-polyethylene oxide block copolymer having different molecular weights are used as precursors of carbon materials to prepare Hollow -Derivatives carbon material as an electrocatalyst through block copolymer self-assembly. The composition and microstructure of the prepared catalysts are shown by Raman spectroscopy, X-ray diffraction (XRD), Test of nitrogen adsorption and desorption curves, High resolution transmission electron microscopy (HR-TEM) and scanning electron microscopy (HR-SEM). Oxygen was passed into alkaline electrolyte solution until the solution reached saturation state. With molecular weight increasing, the obtained sample gradually changed from block to hollow and spherical. When the molecular weight was 12600 g mol^?1, the evenly hollow carbon nanocages was acquired (C-12600). In O₂ saturated alkaline electrolyte (0.1 M KOH solution), C-12600's limited current density，half-wave potential and initial potential are 5.23 mA cm^?2@0.4 V, 0.72 V and 0.81 V, respectively. And most important is that half-wave potential and onset potential have barely change after 2000 cycles of cyclic voltammetry. As a result, the porous carbon materials exhibited excellent electrocatalytic activity while maintaining high stability in alkaline KOH solution.     

Tunable colors and conductivity by electroless growth of Cu/Cu2O particles on sol-gel modified cellulose

Nano Research - Development of colored surfaces by formation of nano-structured aggregates is a widely used strategy in nature to color lightweight structures (e.g. butterflies) without the use of...     

A new perspective of co-doping and Nd segregation effect on proton stability and transportation in Y and Nd co-doped BaCeO3

Bulk and surface properties of proton stability and transportation in Y and Nd co-doped BaCeO₃ (BCYN), especially the effect of Nd segregation, were investigated by first-principles calculations. Since the structure of doped BaCeO₃ at the operating temperature of proton-conducting has been unclear for a long time, we have summarized the latest experimental results and calculated the structure of the asymmetric BCYN for the first time. The results show that compared with Y, Nd doping promotes oxygen vacancy formation, however reduces proton stability. Our calculation can also provide a possible explanation for the formation of space charge layer at the grain boundary of doped BaCeO₃ in experiment. Unlike the stable Y in BCYN, Nd is calculated to be easily segregated, which can facilitate both proton hydration and proton transportation near the surface. Moreover, Nd segregation at the grain boundary is predicted to be beneficial for proton transportation between grains.     

Fabrication of tungsten oxide photoanode by doctor blade technique and investigation on its photocatalytic operation mechanism

WO₃ is a potential material candidate for construction of photoanode for solar driven water splitting. In this work, μm-thick porous WO₃ photoanode is prepared by depositing a stable ink made of WO₃ nanoparticles and Aristoflex velvet polymer in water using the doctor blade technique, followed by a sintering in air. The nature of WO₃ nanoparticles, its loading mass on F-doped tin oxide electrode as well as sintering temperature are examined in order to optimize the photocatalytic activity of the resultant WO₃ photoanode. The operation of WO₃ photoanode is investigated by varying the light illumination direction and light incident intensity as well as changing the nature of the electrolyte. Dissolved tungsten in electrolyte is quantified by ICP-MS providing insights into the influences of electrolyte nature and operating conditions to the corrosion of WO₃. It is proposed that the H₂O₂ and OH^. radical generated as by-products of the photo-driven water oxidation on the photoanode surface are harmful species that accelerate the dissolution of WO₃.     

Study on the removal of olefins from naphtha by clay loaded with trifluoromethanesulfonic acid

Journal of Porous Materials - In this work, a trifluoromethanesulfonic acid (TFOH) modified clay (TFOH-Clay) was developed for the removal of trace olefins in heavy naphtha. 5%TFOH-Clay can...