Review: the latest advances in biomedical applications of chitosan hydrogel as a powerful natural structure with eye-catching biological properties

Journal of Materials Science - Chitosan is one of the natural cationic polymers with unique properties such as non-toxicity, biodegradability, biocompatibility, environmentally friendly that has...     

Compressive strength and wear properties of SiC/Al6061 composites reinforced with high contents of SiC fabricated by pressure-assisted infiltration

Pressure-assisted infiltration was used to synthesize SiC/Al 6061 composites containing high weight percentages of SiC. A combination of PEG and glass water was used to fabricate SiC preforms and the effect of the presence of glass water on the microstructure and mechanical properties of the preforms was evaluated by performing compression tests on the preforms. Also, the compressive strength and the hardness of the SiC/Al composites were investigated. The results revealed that the glass water improved the compressive strength of the preforms by about five times. The microstructural characterization of the composites showed that the penetration of the aluminum melt into the preforms was completed and almost no porosity could be seen in the microstructures of the composites. Moreover, the composite containing 75 wt% SiC exhibited the highest compressive strength as well as the maximum hardness. The results of the wear tests showed that increasing the SiC content reduces the wear rate so that the Al-75 wt% SiC composite has a lower wear rate and a lower coefficient of friction than those of Al-67 wt% SiC composite. This indicated higher wear resistance in these composites than the Al alloy due to the formation of a tribological layer on the surface of the composites.     

Al2O3 Colloidal Nanocrystals with Strong UV Emission

A facile sol–gel procedure has been developed for the synthesis of colloidal alumina nanocrystals. For the first time, optical characterization procedures were employed to study the quantum confinement effects in optical properties of the prepared Al₂O₃ sol. Accordingly, the hyperbolic band model was used to determine the optical band gap of colloidal alumina nanocrystals. X‐Ray diffraction pattern was used to study the crystallographic phase of the dried gel. Morphological characterization was performed using scanning electron microscopy (SEM). Inductively Coupled Plasma (ICP) emission spectroscopy was used to determination purity of the Al₂O₃ powder. High‐resolution TEM showed that the diameter of colloidal nanocrystals is about 10 nm. Photoluminescence spectroscopy demonstrated that quantum yields for colloidal nanocrystals are 68% with 300 nm excitation wavelength. The experimental observations confirm that highly stable alumina sol with strong UV emission was synthesized. The mentioned optical properties have not been reported before.     

Evaporation and Evolution of Suspended Solution Droplets at Atmospheric and Reduced Pressures

Thermal history and solute precipitation behavior of suspended solution droplets of sodium chloride (NaCl), magnesium sulphate (MgSO₄), and zirconium hydroxychloride (ZrO(OH)Cl) evaporating at atmospheric and reduced pressures are studied. Experimental measurements on the variation of droplet diameter, solution concentration, and temperature during the evaporation period are presented and discussed. The results of solute precipitation behavior in solution droplets observed under an optical microscope are displayed and discussed. Results indicate that reducing the pressure (∼ 33 kPa) results in a change in the solution droplet evaporation rate, but the thermal histories of a particular solution droplet are similar at the atmospheric and reduced pressures. At atmospheric and reduced pressures used in this study, the d² law for solution droplets is valid at early stages of the evaporation and before the solute precipitation initiates. Drying of MgSO₄ and ZrO(OH)Cl solution droplets results in the formation of spherical particles, whereas drying of spherical NaCl solution droplets results in the formation of cubic particles.     

A novel open-loop high-speed CMOS sample-and-hold

A new open-loop high-speed CMOS sample-and-hold is presented. Based on new method for further reduction of voltage-dependent charge injection, a new CMOS sample-and-hold was designed. Simulation results confirm the effectiveness of this method. Over 10 dB improvement in signal-to-noise ratio, compared to the signal-to-noise ratio of conventional bottom plate sampling S/Hs was achieved with this method. A comparison between newly designed S/H and the bottom-plate sampling S/H is presented.     

Second-order filter response with series-coupled silica microresonators

We have demonstrated an approach for fabricating a photonic filter with second-order response function. The filter consists of two germania-doped silica microtoroidal or microspherical resonators cascaded in series. We use ultraviolet irradiation to tune the mode of one microcavity to bring it close to the mode of the second microcavity. This approach produces a filter function with much sharper rolloff than can be obtained with the individual microresonators.     

Effect of Reactor Ambient Pressure on the Morphology of Spray Dried Magnesium Sulphate Powders

The effect of reducing the reactor air pressure on the morphology of spray dried magnesium sulphate powders is investigated, experimentally. A reactor, capable of drying and pyrolyzing solution sprays at low pressures, is designed and manufactured. A vibrating mesh nebulizer is employed to generate the spray. Four different pressures, starting from 60 Torr to the atmospheric pressure, and two different reactor air temperatures of 130°C and 420°C, are considered. In addition, two different concentrations of magnesium sulphate solutions are tested. The results are explained based on the effect of reactor air pressure on the droplet evaporation rate.