Calculation of the Characteristics of Salient‐Pole Synchronous Machines Assisted by Permanent Magnets on the Basis of the Operating Principle

In this study we investigate a method for accurately calculating the characteristics of salient‐pole synchronous machines assisted by permanent magnets. First, the operating principle of the machines is investigated by using both finite element analysis and a simple magnetic circuit. Then, a theoretical representation of the assist effect on the permanent magnets is derived based on the magnetic circuit. Finally, the measured and calculated results are compared in order to confirm the validity of the proposed calculation method. We show that the load characteristics of the proposed machine can be accurately estimated from the no‐load and short‐circuit characteristics of the conventional machine without permanent magnets, and the size and magnetization of the inserted permanent magnets.     

Effects of Winding Attachment Positions on Output Characteristics of Flux‐Modulating Synchronous Machines

The flux‐modulating synchronous machine (FMSM) is a new type of multipole SM with nonoverlapping concentrated armature and field windings on the stator. This paper compares the output characteristics of two FMSMs through finite element analysis (FEA) and experiments. In both of the FMSMs, the attachment positions of the armature and field windings are swapped. To determine the reason for the discrepancies in their output characteristics, unsaturated inductances were calculated using a d‐‐q equivalent circuit. In addition, the calculated results of the inductances were confirmed through a visualization of the leakage fluxes using FEA. The results of the study show that the synchronous inductance can be reduced by attaching the armature winding to the air‐gap side of the stator teeth and that the reduction leads to an increase in output power.     

Accumulation of Arsenic and Copper by Bryophytes Growing in an Aquatic Environment near Copper Mine Tailings

Bryophytes with high As accumulation affinity were identified in the aquatic environment. We surveyed a stream near copper mine tailings and then conducted laboratory experiments to confirm As accumulation in the bryophytes with high As affinity. We found that a moss, Scopelophila cataractae, accumulates As in addition to Cu in aquatic environments and confirmed it in laboratory experiments. The highest value for As in S. cataractae from the field survey was 1300 mg/kg dry weight at relatively low As concentrations in the stream water (0.005 mg/L). In addition, Brachythecium plumosum and Rhynchostegium riparioides may also be useful bryophytes for accumulation of Cu and As, though the mechanisms of As accumulation might differ between these two bryophytes and S. cataractae.     

Bioaugmented membrane bioreactor (MBR) with a GAC-packed zone for high rate textile wastewater treatment

The long-term performance of a bioaugmented membrane bioreactor (MBR) containing a GAC-packed anaerobic zone for treatment of textile wastewater containing structurally different azo dyes was observed. A unique feeding strategy, consistent with the mode of evolution of separate waste streams in textile plants, was adopted to make the best use of the GAC-zone for dye removal. Dye was introduced through the GAC-zone while the rest of the colorless media was simultaneously fed through the aerobic zone. Preliminary experiments confirmed the importance of coupling the GAC-amended anaerobic zone to the aerobic MBR and also evidenced the efficacy of the adopted feeding strategy. Following this, the robustness of the process under gradually increasing dye-loading was tested. The respective average dye concentrations (mg/L) in the sample from GAC-zone and the membrane-permeate under dye-loadings of 0.1 and 1 g/L.d were as follows: GAC-zone (3, 105), permeate (0, 5). TOC concentration in membrane-permeate for the aforementioned loadings were 3 and 54 mg/L, respectively. Stable decoloration along with significant TOC removal during a period of over 7 months under extremely high dye-loadings demonstrated the superiority of the proposed hybrid process.     

Distinct Roles of Soluble and Transmembrane Adenylyl Cyclases in the Regulation of Flagellar Motility in Ciona Sperm

Adenylyl cyclase (AC) is a key enzyme that synthesizes cyclic AMP (cAMP) at the onset of the signaling pathway to activate sperm motility. Here, we showed that both transmembrane AC (tmAC) and soluble AC (sAC) are distinctly involved in the regulation of sperm motility in the ascidian Ciona intestinalis. A tmAC inhibitor blocked both cAMP synthesis and the activation of sperm motility induced by the egg factor sperm activating and attracting factor (SAAF), as well as those induced by theophylline, an inhibitor of phoshodiesterase. It also significantly inhibited cAMP-dependent phosphorylation of a set of proteins at motility activation. On the other hand, a sAC inhibitor does not affect on SAAF-induced transient increase of cAMP, motility activation or protein phosphorylation, but it reduced swimming velocity to half in theophylline-induced sperm. A sAC inhibitor KH-7 induced circular swimming trajectory with smaller diameter and significantly suppressed chemotaxis of sperm to SAAF. These results suggest that tmAC is involved in the basic mechanism for motility activation through cAMP-dependent protein phosphorylation, whereas sAC plays distinct roles in increase of flagellar beat frequency and in the Ca²⁺-dependent chemotactic movement of sperm.     

Improvement in thermal endurance of D-mannitol as phase-change material by impregnation into nanosized pores

This paper describes the control of the melting point and improvement of the thermal endurance of D-mannitol (melting point T_m = 440 K) as a phase-change material (PCM) by vacuum impregnation of the PCM into nanosized pores of porous SiO₂ grains. First, we examined the effects of the average pore size (D_P) of porous SiO₂ on T_m and latent heat (L) of PCM/SiO₂ composites. Second, we investigated the thermal endurance of the composites using constant temperature kinetics based on L of the PCM and composites. Third, we performed cyclic tests of melting and freezing on the composite to evaluate leakage of the PCM. Thermophysical properties of the samples were measured by differential scanning calorimetry, and the following results were obtained: (1) The impregnation ratio of the composites was 0.91–0.99; therefore, almost all pores were completely filled with the PCM. (2) T_m shifted to lower temperature with smaller D_P, reaching 413 K in case of the PCM/SiO₂ composite with a D_P of 11.6 nm (3) T_m was derived as a function of D_P from the Gibbs–Thomson equation taking into account the existence of a nonfreezing layer on the surface of the pore wall. (4) The duration of thermal degradation of the PCM/SiO₂ composite with D_P = 11.6 nm was three times longer than that of the pure PCM at a temperature that is 10 K more than each melting point. (5) The PCM/SiO₂ composite with D_P = 11.6 nm can use as a shape-stable PCM composite without leakage of PCM.