以辉锑矿为原料放电等离子烧结快速制备黝铜矿Cu_(12)Sb_4S_(13)及反应机理

采用辉锑矿为原料成功制备出Cu_(12)Sb_4S_(13)块体。研究以Sb_2S_3矿物为原料时烧结工艺对Cu_(12)Sb_4S_(13)合成的影响。在400 ～ 440℃温度区间内均可快速合成Cu_(12)Sb_4S_(13)块体且二次烧结能够进一步减小中间相CuSbS_2和Cu_3SbS_3。第二相Cu_3SbS_4和残留相CuS随着烧结时间的延长而降低。二次烧结前进行机械化球磨处理,干磨比湿磨更容易减小残留相。初次烧结块体的断面SEM和EDS能谱分析表明内部存在Cu或Cu_2S颗粒团聚现象。适当降低Cu或CuS摩尔量(化学计量比0.1 mol)能促进烧结块表面反应进行。烧结过程中,硫磺蒸汽压的导致烧结块表面成分和内部粉末的成分不同。     

Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

Abscopal Effect of Frozen Autograft Reconstruction Combined with an Immune Checkpoint Inhibitor Analyzed Using a Metastatic Bone Tumor Model

We evaluated the abscopal effect of re-implantation of liquid nitrogen-treated tumor-bearing bone grafts and the synergistic effect of anti-PD-1 (programmed death-1) therapy using a bone metastasis model, created by injecting MMT-060562 cells into the bilateral tibiae of 6–8-week-old female C3H mice. After 2 weeks, the lateral tumors were treated by excision, cryotreatment using liquid nitrogen, excision with anti-PD-1 treatment, and cryotreatment with anti-PD-1 treatment. Anti-mouse PD-1 4H2 was injected on days 1, 6, 12, and 18 post-treatment. The mice were euthanized after 3 weeks; the abscopal effect was evaluated by focusing on growth inhibition of the abscopal tumor. The re-implantation of frozen autografts significantly inhibited the growth of the remaining abscopal tumors. However, a more potent abscopal effect was observed in the anti-PD-1 antibody group. The number of CD8+ T cells infiltrating the abscopal tumor and tumor-specific interferon-γ (IFN-γ)-producing spleen cells increased in the liquid nitrogen-treated group compared with those in the excision group, with no significant difference. The number was significantly higher in the anti-PD-1 antibody-treated group than in the non-treated group. Overall, re-implantation of tumor-bearing frozen autograft has an abscopal effect on abscopal tumor growth, although re-implantation of liquid nitrogen-treated bone grafts did not induce a strong T-cell response or tumor-suppressive effect.     

Perspective of mixed matrix membranes for carbon capture

Polymeric membrane-based gas separation has found wide applications in industry, such as carbon capture, hydrogen recovery, natural gas sweetening, as well as oxygen enrichment. Commercial gas separation membranes are required to have high gas permeability and selectivity, while being cost-effective to process. Mixed matrix membranes (MMMs) have a composite structure that consists of polymers and fillers, therefore featuring the advantages of both materials. Much effort has been made to improve the gas separation performance of MMMs as well as general membrane properties, such as mechanical strength and thermal stability. This perspective describes potential use of MMMs for carbon capture applications, explores their limitations in fabrication and methods to overcome them, and addresses their performance under industry gas conditions.     

Dynamic probe of ZnTe(110) surface by scanning tunneling microscopy

The reconstructed surface structure of the II–VI semiconductor ZnTe (110), which is a promising material in the research field of semiconductor spintronics, was studied by scanning tunneling microscopy/spectroscopy (STM/STS). First, the surface states formed by reconstruction by the charge transfer of dangling bond electrons from cationic Zn to anionic Te atoms, which are similar to those of IV and III–V semiconductors, were confirmed in real space. Secondly, oscillation in tunneling current between binary states, which is considered to reflect a conformational change in the topmost Zn–Te structure between the reconstructed and bulk-like ideal structures, was directly observed by STM. Third, using the technique of charge injection, a surface atomic structure was successfully fabricated, suggesting the possibility of atomic-scale manipulation of this widely applicable surface of ZnTe.     

Detection of Multiple Blockages in Parallelized Microreactors

In a plant consisting of parallelized microreactors (MRs), the product quality is lowered because of a lack of flow uniformity among them when blockage occurs. It is not practical to install sensors in every MR from the viewpoint of cost when detecting the blocked MRs. In the previous study, the multiple blockage detection (MBD) method using a small number of sensors was proposed, but its performance became low when the number of sensors decreased. Here, the conventional algorithm for MBD is improved by considering the process behavior on blockage occurrence, and the effectiveness of the improved algorithm is demonstrated through a numerical case study. The effects of flow distributor types and sensor types on the MBD performance are numerically investigated.     

Resinification Behavior of Regenerated Feather Keratin Powder

A preliminary study was performed on the resinification behavior of regenerated feather keratin powder by changing the sintering conditions, and the thermal and mechanical properties for the obtained resin were investigated. It was confirmed that the molding at 140°C was enough to complete the resinification. The resin obtained was amorphous and its glass transition temperature could be raised to 93°C. In addition, the hardness of the resin could be increased from 20–25 HV to 90 HV by leaving the as-sintered compact resin in ambient air at room temperature for 133 days. Crosslinking agents that work even at room temperature seem to be synthesized during the molding.     

Thermal and optical properties of hyperbranched fluorinated polyimide/mesoporous SiO2 nanocomposites exhibiting high transparency and reduced thermo-optical coefficients

A series of hyper-branched polyimide (HBPI)/mesoporous SiO₂ nanocomposite films were prepared from a fluorinated anhydride (6FDA), a fluorinated triamine (TFAPOB), and mesoporous SiO₂ nanoparticles (NPs). The anhydride-terminated precursor of HBPI was functionalized using a coupling agent prior to mixing with SiO₂ NPs. The morphologies and thermal-optical properties of the nanocomposite films were investigated, with particular focus on their optical transparency, refractive indices (n), and thermo-optical (TO) coefficients. The absolute values of TO coefficients (|dn/dT|) of HBPI film (50.8 ppm/K) were significantly reduced to 13.4 ppm/K by homogeneous dispersion of 15 wt% of SiO₂ NPs. The HBPI/SiO₂ composite films exhibited high thermal stability without significant weight loss of up to 400 °C in air. The films also exhibited small coefficients of linear thermal expansion (CTEs) within the range 30–40 ppm/K. In addition, enhanced interfacial interactions between SiO₂ and HBPI significantly improve the optical transparency with cutoff wavelengths shorter than 450 nm. The refractive indices of HBPI/SiO₂ composite films were found to range from 1.477 to 1.502, which agrees well with the calculated values. This study shows that the incorporation of SiO₂ NPs in multi-functional HBPI matrix is a promising approach to prepare high performance thermally stable films for thermo-optic applications.