Fire safe,sustainable loose furnishing

The aim of this exploratory study has been to investigate the fire properties and environmental aspects of different upholstery material combinations, mainly for domestic applications. An analysis of the sustainability and circularity of selected textiles, along with lifecycle assessment, is used to qualitatively evaluate materials from an environmental perspective. The cone calorimeter was the primary tool used to screen 20 different material combinations from a fire performance perspective. It was found that textile covers of conventional fibres such as wool, cotton and polyester, can be improved by blending them with fire resistant speciality fibres. A new three‐dimensional web structure has been examined as an alternative padding material, showing preliminary promising fire properties with regard to ignition time, heat release rates and smoke production.     

Influence of pressure and dwell time on pressure-assisted sintering of calcium cobaltite

Calcium cobaltite Ca₃Co₄O₉, abbreviated Co349, is a promising thermoelectric material for high-temperature applications in air. Its anisotropic properties can be assigned to polycrystalline parts by texturing. Tape casting and pressure-assisted sintering (PAS) are a possible future way for a cost-effective mass-production of thermoelectric generators. This study examines the influence of pressure and dwell time during PAS at 900°C of tape-cast Co349 on texture and thermoelectric properties. Tape casting aligns lentoid Co349. PAS results in a textured Co349 microstructure with the thermoelectrically favorable ab-direction perpendicular to the pressing direction. By pressure variation during sintering, the microstructure of Co349 can be tailored either toward a maximum figure of merit as required for energy harvesting or toward a maximum power factor as required for energy harvesting. Moderate pressure of 2.5 MPa results in 25% porosity and a textured microstructure with a figure of merit of 0.13 at 700°C, two times higher than the dry-pressed, pressureless-sintered reference. A pressure of 7.5 MPa leads to 94% density and a high power factor of 326 µW/mK² at 800°C, which is 11 times higher than the dry-pressed reference (30 MPa) from the same powder.     

Improving Properties of Poly(vinylidene fluoride) by Adding Expanded Graphite without Surface Modification via Water‐Assisted Mixing Extrusion

Expanded graphite (EG) is introduced into poly(vinylidene fluoride) (PVDF) by melt mixing extrusion with water injection. The results demonstrate that the unfunctionalized EG in composite prepared with water injection exbibits better dispersion than that in the one prepared without water injection due to the promoting role of water during extrusion. Thus, the PVDF/EG composite with loading of 4 wt% prepared by water‐assisted mixing extrusion (WAME) exhibits electrical conductivity of about three orders of magnitude higher than the neat PVDF and one order of magnitude higher than the one prepared without water injection. Comparing to the neat PVDF, the thermal conductivity of the composites prepared with and without water injection is increased by 101.5% and 75.0%, respectively. The introduced EG leads to increased Young’s modulus and tensile strength especially for the composite prepared by WAME. The present work indicates that WAME can promote the dispersion of EG in PVDF matrix without any extra functionalization.     

Chia Seed Oil Prevents High Fat Diet Induced Hyperlipidemia and Oxidative Stress in Mice

Hyperlipidemia is a common cardiovascular disease. At present, the influence of high fat diet (HFD) on this is being explored. Recently, vegetable oils rich in omega‐3 have been reported that can treat hyperlipidemia caused by HFD. However, the effects of chia seed oil (CSO) on HFD‐induced hyperlipidemia and oxidative stress are poorly studied. Hence, in this study, the effects of CSO on hyperlipidemia and oxidative stress induced by HFD in mice are analyzed by various commercial kits, section staining, and protein expression. The results show that CSO decreases body weight and organ index. Meanwhile, CSO reduces serum lipid levels of total cholesterol, triglyceride, and low‐density lipoprotein cholesterol. It can also elevate superoxide dismutase and glutathione peroxidase activities and reduce malondialdehyde content in serum and liver. The results of histopathological analysis prove that CSO improves hepatic steatosis and reduces lipid deposition. Further, the results of western blot demonstrate that CSO upregulates the expression of peroxisome proliferator‐activated receptor alpha and carnitine palmitoyltransferase 1a in the liver. As a result, CSO may be a potential lipid‐lowering oil to prevent and treat HFD‐induced hyperlipidemia and oxidative stress. Practical Applications CSO, as a byproduct of chia seed processing, is a rich source of α‐linolenic acid. This study investigates the effects of CSO on HFD‐induced hyperlipidemia and oxidative stress in mice. It is concluded that dietary CSO can improve the hyperlipidemia in HFD‐induced mice via analysis of lipid parameters, histopathology study of the liver, and lipid metabolism related genes. In addition, supplementation of CSO also can improve the oxidative stress in mice. Therefore, CSO can be used for the prevention of hyperlipidemia and oxidative stress. This research provides a theoretical basis for the comprehensive development and utilization of functional chia seed oil.     

Delay compensated control of the Stefan problem and robustness to delay mismatch

This paper presents a control design for the one‐phase Stefan problem under actuator delay via a backstepping method. The Stefan problem represents a liquid‐solid phase change phenomenon which describes the time evolution of a material's temperature profile and the interface position. The actuator delay is modeled by a first‐order hyperbolic partial differential equation (PDE), resulting in a cascaded transport‐diffusion PDE system defined on a time‐varying spatial domain described by an ordinary differential equation (ODE). Two nonlinear backstepping transformations are utilized for the control design. The setpoint restriction is given to guarantee a physical constraint on the proposed controller for the melting process. This constraint ensures the exponential convergence of the moving interface to a setpoint and the exponential stability of the temperature equilibrium profile and the delayed controller in the norm. Furthermore, robustness analysis with respect to the delay mismatch between the plant and the controller is studied, which provides analogous results to the exact compensation by restricting the control gain.     

An efficient method of generating vortex electromagnetic wave based on double‐layer transmissive metasurface

A broadband double‐layer transmissive metasurface (TMS) for effective generate vortex electromagnetic wave is presented in this paper. The proposed TMS consists of two types of elements. The first element is composed of a multi‐resonant dipole and four metal vias. The metal vias increase the coupling strength between the upper and lower layers to improve transmission efficiency. On the basis of the first element, the second element adds stubs to ensure sufficient phase shift. The far‐field cross polarisation is eliminated by special element arrangement. Then, a centre‐fed linear polarisation TMS is designed to generate orbital angular momentum beams with mode l = ? 1. The proposed TMS is designed, manufactured and measured to verify the proposed design. The measured results indicate that a maximum gain of 20.8 dBi and narrow divergence angle of ±5° are achieved at 18 GHz. Furthermore, mode purity is higher than 86.1% within the 17 to 19 GHz band. The proposed double‐layer TMS saved costs, reduced weight and without assembly error is a good candidate for OAM generator.     

Perception‐aware autonomous mast motion planning for planetary exploration rovers

Highly accurate real‐time localization is of fundamental importance for the safety and efficiency of planetary rovers exploring the surface of Mars. Mars rover operations rely on vision‐based systems to avoid hazards as well as plan safe routes. However, vision‐based systems operate on the assumption that sufficient visual texture is visible in the scene. This poses a challenge for vision‐based navigation on Mars where regions lacking visual texture are prevalent. To overcome this, we make use of the ability of the rover to actively steer the visual sensor to improve fault tolerance and maximize the perception performance. This paper answers the question of where and when to look by presenting a method for predicting the sensor trajectory that maximizes the localization performance of the rover. This is accomplished by an online assessment of possible trajectories using synthetic, future camera views created from previous observations of the scene. The proposed trajectories are quantified and chosen based on the expected localization performance. In this study, we validate the proposed method in field experiments at the Jet Propulsion Laboratory (JPL) Mars Yard. Furthermore, multiple performance metrics are identified and evaluated for reducing the overall runtime of the algorithm. We show how actively steering the perception system increases the localization accuracy compared with traditional fixed‐sensor configurations.