Altered age-hardening behavior in the ultrafine-grained surface layer of Mg-Zn-Y-Ce-Zr alloy processed by sliding friction treatment

To gain insight into the ageing behavior of ultrafine grain(UFG)structure,the precipitation phenom-ena and microstructural evolutions of Mg-6Zn-1Y-0.4Ce-0.5 Zr(wt.％)alloy processed by sliding friction treatment(SFT)were systematically studied using hardness texting,transmission electron microscopy(TEM)equipped with high-angle annular dark-field scanning(HADDF-STEM),X-ray diffraction(XRD)and XRD line broadening analysis.The microhardness of the SFT-processed(SFTed)sample initially decreases from 109.6 HV to 104.8 HV at ageing for 8 h,and then increases to the peak-ageing point of 115.4 HV at 16 h.Subsequently,it enters the over-aged period.The un-SFTed sample,as the counterpart,follows a regular ageing behavior that increases from 89.9 HV to 99.6 HV when ageing for 12 h,and then drops.A multi-mechanistic model is established to describe the strengthening due to grain refinement,disloca-tion accumulation,precipitation etc.The analysis reveals that the temperature sensitive UFG structure has an obvious grain coarsening effect,which arouses the soft phenomenon in the early ageing stage.But precipitation hardening provides an excellent hardness enhancement for overcoming the negative influ-ence and helping to reach the peak-aged point.In our microstructural observations,a lot of equilibrium ultrafine MgZn2 precipitates precipitate along dislocations because defects can provide the favorable conditions for the migration and segregation of solute atoms.     

An integrated model for analysing the effects of ultrasonic vibration on tool torque and thermal processes in friction stir welding

An integrated model of ultrasonic vibration enhanced friction stir welding (UVeFSW) is developed by integrating the thermal-fluid model with the ultrasonic field model and tool torque model. The tool torque and the heat generation rate at tool/workpiece contact interfaces are coupled with the interfacial temperature, strain rate and ultrasonic energy density. The model is used in quantitatively analysing the effects of ultrasonic vibration on tool torque and thermal processes in friction stir welding (FSW). The results show that ultrasonic vibration reduces the flow stress, which results in a decreasing of tool torque, interfacial heat generation rate and interfacial temperature. The complicated interaction of ultrasonic energy with the thermal processes in FSW leads to a gentle thermal gradient and an enhanced plastic material flow in UVeFSW. The model is validated by a comparison of the calculated thermal cycles and tool torque at various welding parameters with the experimentally measured ones.     

Tribological behavior of composites fabricated by reactive SPS sintering in Ti-Si-C system

In this study, wear and friction behavior of two based-composites from the Ti-Si-C system, (40 wt% TiC; 28 wt% Ti₅Si₃; 17 wt% Ti₃SiC₂) and (18 wt% TiC; 26 wt% Ti₅Si₃; 41 wt% Ti₃SiC₂) reinforced by 15 wt% of large size SiC (100-150 µm) particles were investigated. The four-phase composites exhibited approximatively the same friction coefficient (µ ~ 0.9) under high loads (10 N and 7 N). The composite with high Ti₃SiC₂ showed higher wear rate values by one order of magnitude. However, under 1 N, the composite with high TiC content showed a higher running-in period and a lower steady state µ value (0.37 after 1000 m sliding distance). Scanning electron microscopy, Energy Dispersive X-Ray and Raman spectroscopy analysis of the worn surfaces of the two composites revealed that oxidation was the dominant wear mechanism. The oxidation process and the removal kinetics of the oxides during sliding controlled the tribological behavior of the composites. The influence of processing variables on microstructures development and wear mechanisms of the composites is discussed.     

天然橡胶/顺丁橡胶/丁苯橡胶自润滑喷蜡橡胶材料的性能

在天然橡胶(NR)/顺丁橡胶(BR)/丁苯橡胶(SBR)为基体的自润滑喷蜡橡胶材料中加入芥酸酰胺,考察芥酸酰胺作为润滑剂时对NR/BR/SBR自润滑喷蜡橡胶材料的硫化特性、力学性能、门尼黏度、摩擦系数及耐老化性能的影响。结果表明,与未加芥酸酰胺的胶料相比,当芥酸酰胺用量为10份时,胶料转矩减小,焦烧时间和正硫化时间缩短,扯断伸长率从388%增加至523%,拉伸强度降低了21.36%,邵尔A硬度、压缩永久变形分别下降5.56%和8.74%,动、静摩擦系数分别减小23.46%和24.82%,门尼黏度降低20.89%,耐热氧老化性能下降。硫化胶拉伸100%停放5 min后,表面出现明显的白色润滑膜,胶料流动性变好,各组分分散得更均匀,断面更光滑。     

机械合金化FeS/Cu复合材料的摩擦磨损性能

以FeS和CuSn8Ni1粉末为原料，利用机械合金化技术和粉末冶金技术制备了FeS/Cu复合材料，探讨了不同载荷情况下所制备的FeS/Cu复合材料的摩擦学性能及润滑膜与转移膜特征。结果表明：机械合金化提高了FeS与铜合金基体界面结合性能，进而提高了材料减摩耐磨性能；当载荷较小时，摩擦副表面接触不稳定，复合转移膜不连续，摩擦因数波动大；载荷较大时，复合转移膜易破损，材料的减摩耐磨性能变差；当载荷为150 N时，载荷适宜，材料表面软化，复合转移膜更加完整，摩擦因数较小。     

Process and joint quality of ultrasonic vibration enhanced friction stir lap welding

In order to improve the process effectiveness and joint quality, ultrasonic vibrations were integrated with friction stir lap welding. Effect of ultrasonic exertion on the process and joint quality of AA 6061-T6 were investigated. Upon ultrasonic exertion, joints owned larger effective lap width, shorter hooks and improved strength. Weld fracture mode changed from a ductile–brittle mixed mode to a more ductile mode while the fracture path shifted from lap interface to beyond the stir zone. Material flow and interface defects were characterised using lap welded dissimilar aluminium alloy joints. Ultrasonic vibration improved the material flow and reduced the interfacial defects. Variations in failure load of joints were found in accordance with the variations in material flow and interfacial defects.     

Stochastic analysis of strongly non-linear elastic impact system with Coulomb friction excited by white noise

The stochastic response of frictionally damped strongly non-linear elastic impact oscillator subjected to white noise excitation and its stochastic bifurcation are considered. By the stochastic averaging method based on generalized harmonic function, one can obtain the stationary probability density function of this system. The effects of system parameters on the responses are investigated and the analytical results were verified by comparing with numerical results from Monte Carlo simulations. Stochastic bifurcations are discussed through a qualitative change of the stationary probability distribution, which indicates that the coefficient of friction, damping constant of the elastic impact force respectively, can be treated as bifurcation parameters.     

一种液压摩擦焊机电液系统研究与试验

针对海上石油平台、海底输送管线维修的需要,提供了一种液压摩擦焊机液压和电器系统设计思路,通过参数计算、电液控制系统设计,研发了一种液压摩擦焊机,通过对DH38钢摩擦叠焊单元成型工艺试验,发现焊接接头拉伸强度达到了母材强度的76%以上,验证了液压摩擦焊机的可靠性能,通过该研究的应用,可对海上石油平台、海底输送管线的维修起到积极作用。     

类富勒烯碳薄膜的结构演变及摩擦学性能研究

通过等离子体增强化学气相沉积技术,以不同沉积时间在硅表面上制备类富勒烯碳薄膜,探究类富勒烯碳薄膜结构演变和摩擦学性能随沉积时间变化规律。利用拉曼光谱和透射电子显微镜,考察类富勒烯碳薄膜微结构和表面形貌随沉积时间的变化。结果表明:碳薄膜内类富勒烯结构含量随沉积时间先增加后保持不变;采用沉积时间为3 h的类富勒烯碳薄膜组成摩擦配伍对,当载荷从8 N增加到14 N时,摩擦因数从0.013降至0.006,即随载荷的增加实现了由低摩擦向超滑的转变。这是因为摩擦诱使类富勒烯碳薄膜发生结构转变,并形成有利于减少摩擦的类球状或外部石墨壳层闭合的纳米颗粒。