Microstructure and stress corrosion cracking of the fusion boundary region in an alloy 182-A533B low alloy steel dissimilar weld joint

Stress corrosion cracking (SCC) in the fusion boundary (FB) region of an Alloy 182-A533B low alloy steel (LAS) dissimilar weld joint in high temperature water doped with sulfate was studied following a microstructure characterization of the FB region. The microstructure characterization suggested the type-II and type-I boundaries in the dilution zone (DZ) adjacent to the FB had lower resistance to SCC growth than the FB. Crack propagating perpendicular to the FB in the DZ was observed to be blunted by pitting at the FB, followed by the reactivation from the pitting by localized oxidation along the grain boundary in LAS.     

Anomalous surface morphology of iron generated after anodic dissolution under magnetic fields

The effects of applied magnetic fields on the anodic dissolution of iron in a sulfuric acid solution were studied by potentiodynamic polarization measurements and electrode morphology observations. Uneven anodic dissolution occurs in the presence of magnetic field and the extent of the electrode surface inhomogeneity increases with magnetic flux density. Severely local dissolution at two edge areas of the iron electrode in the presence of magnetic fields is caused by the inhomogeneous distribution of the magnetic flux density at the ferromagnetic iron electrode and the resultant enhancement of the mass transport rate of interfacial film at local areas.     

In situ X-ray diffraction of surface oxide on type 430 stainless steel in breakaway condition using synchrotron radiation

Changes in the crystal structure of type 430 stainless steel and the oxides on its surface were studied in situ at 1373 K using a high-intensity synchrotron X-ray source provided by SPring-8 in Japan. The surface of the steel was initially covered with Cr₂O₃, which was then converted to FeCr₂O₄, and finally Fe₃O₄ and Fe₂O₃ formed on it. These results indicated that the reason for the breakaway oxidation in type 430 stainless steel is Cr depletion beneath Cr₂O₃ layer and the subsequent ionisation of Fe, not the simple mechanical failure of Cr₂O₃.     

Decomposition and regeneration of methane in the absence and the presence of a hydrogen-absorbing alloy CaNi5

Suitable catalysts for the decomposition of methane into carbon and hydrogen and for the regeneration of methane by hydrogenation of the carbon have been looked for in a series of transition metals and precious metals supported on various carriers. The most active catalyst for both reactions was Ni/SiO₂. The carbon formed on this catalyst was thermodynamically less stable than graphite. The different rate equations for the decomposition of methane obtained for the fresh and carbon deposited Ni/SiO₂ suggest that the rate-determining steps are different for the two catalysts. The highest number of carbon atoms deposited per one Ni atom was 31 at 773 K. However, the number of methane molecules recovered easily at 773 K was limited to 1.5 per Ni atom.

A physical mixture of Ni/SiO₂ and CaNi₅, a hydrogen-absorbing alloy, enhanced the decomposition rate of methane, enabling the complete conversion of methane at 773 K beyond the thermodynamic limitation. The presence of CaNi₅ at 273 K separated from the catalyst in a reaction system further enhanced the decomposition of methane due to an increased hydrogen-absorbing capacity of the CaNi₅ at low temperatures. The carbon deposited on Ni/SiO₂ in this case was reactive to be hydrogenated back to methane at 773 K, giving an average 7.5 CH₄ molecules per one Ni atom.     

Photocatalytic decomposition of 2-propanol in air by mechanical mixtures of TiO2 crystalline particles and silicalite adsorbent: The complete conversion of organic molecules strongly adsorbed within zeolitic channels

Fundamental photocatalytic behaviors were investigated for mechanical mixtures of TiO₂ crystalline particles (P25) and MFI type zeolite (silicalite) in the decomposition reaction of 2-propanol vapor in air for the first time. Mechanical mixing enables reliable comparisons to be made between photocatalysts because the contents of TiO₂ and the adsorbent can be widely varied (51 times in this study) while keeping the particle size and crystallinity of TiO₂ unchanged. That is, the use of mechanical mixture highlights the behavior of molecules adsorbed in the microporous crystals, keeping the TiO₂ unchanged. In the case of the mixed photocatalysts, the initial 2-propanol concentration in the gas phase was significantly reduced because of adsorption into the zeolite. After photo-irradiation started, 2-propanol was decomposed to CO₂ with no (or trace amount of) acetone detected in the gas phase. The analysis of final amount of CO₂ formed by the decomposition demonstrated that just by the mechanical mixing of TiO₂ and zeolite, the TiO₂ photocatalyst decomposed completely the reactant and intermediate molecules strongly adsorbed into the zeolite. On the other hand, in reference experiments in which TiO₂ and zeolite were not mixed and were separately placed in a photoreactor, the organic compounds strongly adsorbed in the zeolite could not be decomposed to CO₂ by the photocatalyst. It is notable that the CO₂ formation rates for the mixed photocatalysts were mostly constant for those comprising 40 wt% or larger amounts of zeolite, while being slower than for pure TiO₂. The rate-determining step was discussed based on these data. The present study showed that the mixed photocatalyst could remove organic vapors by adsorption in the dark and decompose completely to CO₂ at moderate reaction rates under photo-irradiation with minimized evolution of intermediate molecules into the gas phase.     

低能离子束辅照对溅射镀TiN膜生长的影响

用诱导型等离子体辅助磁控溅射装置在Si（100）表面低温沉积TiN膜，研究了高密度低能量（≈20eV）离子束辅照对溅射镀TiN膜生长、结构和性能的影响．结果表明，高密度低能离子束辅照会改变TiN膜的择优生长方向并使薄膜致密化。即使沉积温度低于150℃，当入射基板离子数和Ti原子数的比值Ji／JTi≥4.7时，沉积的TiN膜仍可具有完全的（200）面择优生长，薄膜微观结构致密，硬度达到25GPa，残余压应力小．     

Structure and gas permeation properties of asymmetric polyimide membranes made by dry–wet phase inversion: Influence of the polyimide molecular weight

In this article, we report the influence of the polyimide molecular weight (1.2 × 10⁵, 2.6 × 10⁵, and 4.1 × 10⁵) on the structure and the gas permeation properties of asymmetric polyimide membranes made by the dry–wet phase‐inversion process. The apparent skin layer thickness of the asymmetric membrane increased with increasing molecular weight, and the thicknesses of the membranes prepared from the three polyimides with a casting polymer solution containing 8.0 wt % butanol were 132, 350, and 739 nm, respectively. That is, the gas permeance in the asymmetric membranes increased with decreasing molecular weight. In contrast, the gas selectivity of the asymmetric membranes did not depend on the skin layer thickness. The solvent evaporation in the dry phase‐inversion process and the nonsolvent diffusion in the dry process were important factors that determined the formation of the asymmetric membrane. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Supramolecular Zn(II)-Dipicolylamine-Azobenzene-Aminocyclodextrin-ATP Complex: Design and ATP Recognition in Water

Cyclodextrins (CyDs) are water-soluble host molecules possessing a nanosized hydrophobic cavity. In the realm of molecular recognition, this cavity is used not only as a recognition site but also as a reaction medium, where a hydrophobic sensor recognizes a guest molecule. Based on the latter concept, we have designed a novel supramolecular sensing system composed of Zn(II)-dipicolylamine metal complex-based azobenzene (1-Zn) and 3A-amino-3A-deoxy-(2AS,3AS)-γ-cyclodextrin (3-NH₂-γ-CyD) for sensing adenosine-5′-triphosphate (ATP). 1-Zn showed redshifts in the UV-Vis spectra and induced circular dichroism (ICD) only when both ATP and 3-NH₂-γ-CyD were present. Calculations of equilibrium constants indicated that the amino group of 3-NH₂-γ-CyD was involved in the formation of supramolecular 1-Zn/3-NH₂-γ-CyD/ATP. The Job plot of the ICD spectral response revealed that the stoichiometry of 1-Zn/3-NH₂-γ-CyD/ATP was 2:1:1. The pH effect was examined and 1-Zn/3-NH₂-γ-CyD/ATP was most stable in the neutral condition. The NOESY spectrum suggested the localization of 1-Zn in the 3-NH₂-γ-CyD cavity. Based on the obtained results, the metal coordination interaction of 1-Zn and the electrostatic interaction of 3-NH₂-γ-CyD were found to take place for ATP recognition. The “reaction medium approach” enabled us to develop a supramolecular sensing system that undergoes multi-point interactions in water. This study is the first step in the design of a selective sensing system based on a good understanding of supramolecular structures.     

Contribution of Invariant Natural Killer T Cells to the Clearance of Pseudomonas aeruginosa from Skin Wounds

Chronic infections are considered one of the most severe problems in skin wounds, and bacteria are present in over 90% of chronic wounds. Pseudomonas aeruginosa is frequently isolated from chronic wounds and is thought to be a cause of delayed wound healing. Invariant natural killer T (iNKT) cells, unique lymphocytes with a potent regulatory ability in various inflammatory responses, accelerate the wound healing process. In the present study, we investigated the contribution of iNKT cells in the host defense against P. aeruginosa inoculation at the wound sites. We analyzed the re-epithelialization, bacterial load, accumulation of leukocytes, and production of cytokines and antimicrobial peptides. In iNKT cell–deficient (Jα18KO) mice, re-epithelialization was significantly decreased, and the number of live colonies was significantly increased, when compared with those in wild-type (WT) mice on day 7. IL-17A, and IL-22 production was significantly lower in Jα18KO mice than in WT mice on day 5. Furthermore, the administration of α-galactosylceramide (α-GalCer), a specific activator of iNKT cells, led to enhanced host protection, as shown by reduced bacterial load, and to increased production of IL-22, IL-23, and S100A9 compared that of with WT mice. These results suggest that iNKT cells promote P. aeruginosa clearance during skin wound healing.     

A three-dimensional,clothed human thermal model

We have developed a three-dimensional clothed human thermal model for predicting physiological responses to temperature and humidity within clothing by considering the thermal properties of fabrics, clothing ensembles, and their designs. The model is a coupled simulation system of a human thermal model and a clothing thermal model. The model performance was investigated by comparing its predictions with experimental data. The following results were obtained. (1) The model predictions of skin temperature distributions and the micro-climate within clothing basically agreed with experimental data. (2) The skin temperatures of clothed body parts were higher than the corresponding body parts in the nude condition, and the skin temperatures of the hand and foot were higher than those in the nude condition, both in the model predictions and in the experimental data. (3) The model prediction of total moisture transfer was almost the same as obtained from the experimental data. 1998 Scripta Technica, Heat Trans Jpn Res, 26(8): 554–566, 1997