SiN钝化前的NF3等离子体处理对AlGaN/GaN HEMT性能的影响

研究了SiN钝化前利用感应耦合等离子体(ICP)对AlGaN/GaN HEMT表面进行NF3等离子体处理对器件性能的影响.结果表明,运用低能量的NF3等离子体处理钝化前的AlGaN/GaN HEMT表面能有效抑制器件电流崩塌,而器件直流及微波小信号特性则未受影响.微波功率测试表明,经过6min NF3等离子体处理的AIGaN/GaN HEMT在2GHz,30V工作电压下达到6.15W/mm的输出功率密度,而未经过处理的器件只达到1.82W/mm的输出功率密度.     

非掺杂AlGaN/GaN微波功率HEMT

报道了研制的AlGaN/GaN微波功率HEMT,该器件采用以蓝宝石为衬底的非掺杂AlGaN/GaN异质结构,器件工艺采用了Ti/Al/Ni/Au欧姆接触和Ni/Au肖特基势垒接触以及SiN介质进行器件的钝化.研制的200μm栅宽T型布局AlGaN/GaN HEMT在1.8GHz,Vds=30V时输出功率为28.93dBm,输出功率密度达到3.9W/mm,功率增益为15.59dB,功率附加效率(PAE)为48.3%.在6.2GHz,Vds=25V时该器件输出功率为27.06dBm,输出功率密度为2.5W/mm,功率增益为10.24dB,PAE为35.2%.     

蓝宝石衬底上槽栅型X波段增强型AlGaN/GaN HEMT

研制了一款X波段增强型AlGaN/GaN高电子迁移率晶体管(HEMT)。在3英寸(1英寸=2.54 cm)蓝宝石衬底上采用低损伤栅凹槽刻蚀技术制备了栅长为0.3μm的增强型AlGaN/GaN HEMT。所制备的增强型器件的阈值电压为0.42 V,最大跨导为401 mS/mm,导通电阻为2.7Ω·mm。器件的电流增益截止频率和最高振荡频率分别为36.1和65.2 GHz。在10 GHz下进行微波测试,增强型AlGaN/GaN HEMT的最大输出功率密度达到5.76 W/mm,最大功率附加效率为49.1%。在同一材料上制备的耗尽型器件最大输出功率密度和最大功率附加效率分别为6.16 W/mm和50.2%。增强型器件的射频特性可与在同一晶圆上制备的耗尽型器件相比拟。     

SiN钝化对W波段AlGaN/GaN HEMT射频性能的影响

在SiC衬底上制备了栅长为110 nm、漏源间距为2μm的W波段AlGaN/GaN高电子迁移率场效应晶体管(HEMT),分析了SiN钝化对器件直流和射频特性的影响.研究发现:100 nm SiN钝化可显著提升器件的漏源饱和电流及峰值跨导,漏源饱和电流从1.27 A/mm增加至1.45 A/mm (Vgs=1 V),器件峰值跨导从300 mS/mm提升至370 mS/mm,这是由于SiN钝化显著提高了AlGaN/GaN异质结材料沟道电子浓度.此外,SiN钝化可有效抑制器件电流崩塌,显著改善器件直流回扫特性.然而,由于沟道电子浓度增大,钝化后器件中短沟效应增强,器件夹断特性变差.此外,SiN钝化后W波段AlGaN/GaN HEMTs的射频特性得到显著改善,器件的电流增益截止频率从钝化前的33 GHz提升至107 GHz,最高振荡频率从钝化前的65 GHz提升至156 GHz.     

14W X波段AlGaN/GaN HEMT功率MMIC

报道了研制的SiC衬底AIGaN/GaN HEMT微带结构微波功率MMIC,芯片工艺采用凹槽栅场板结构提高AlGaN/GaNHEMTs的微波功率特性.S参数测试结果表明AlGaN/GaN HEMTs的频率特性随器件的工作电压变化显著.研制的该2级功率MMIC在9～11GHz带内30V工作,输出功率大于10W,功率增益大于12dB,带内峰值输出功率达到14.7W,功率增益为13.7dB,功率附加效率为23%,该芯片尺寸仅为2.0mm×1.1mm.与已发表的X波段AlGaN/GaN HEMT功率MMIC研制结果相比,本项工作在单位毫米栅宽输出功率和芯片单位面积输出功率方面具有优势.     

14W X波段AlGaN/GaN HEMT功率MMIC

报道了研制的SiC衬底AIGaN/GaN HEMT微带结构微波功率MMIC,芯片工艺采用凹槽栅场板结构提高AlGaN/GaNHEMTs的微波功率特性.S参数测试结果表明AlGaN/GaN HEMTs的频率特性随器件的工作电压变化显著.研制的该2级功率MMIC在9～11GHz带内30V工作,输出功率大于10W,功率增益大于12dB,带内峰值输出功率达到14.7W,功率增益为13.7dB,功率附加效率为23%,该芯片尺寸仅为2.0mm×1.1mm.与已发表的X波段AlGaN/GaN HEMT功率MMIC研制结果相比,本项工作在单位毫米栅宽输出功率和芯片单位面积输出功率方面具有优势.     

高性能1mm SiC基AlGaN/GaN功率HEMT研制

在6H-SiC衬底上,外延生长了AlGaN/GaN HEMT结构,设计并实现了高性能1mm AlGaN/GaN微波功率HEMT,外延材料利用金属有机物化学气相淀积技术生长.测试表明,该lmm栅宽器件栅长为0.8μm,输出电流密度达到1.16A/mm,跨导为241mS/mm,击穿电压＞80V,特征频率达到20GHz,最大振荡频率为28GHz.5.4GHz连续波测试下功率增益为14.2dB,输出功率达4.1W,脉冲条件测试下功率增益为14.4dB,输出功率为5.2W,两端口阻抗特性显示了在微波应用中的良好潜力.     

高性能1mm SiC基AlGaN/GaN功率HEMT研制

在6H-SiC衬底上,外延生长了AlGaN/GaN HEMT结构,设计并实现了高性能1mm AlGaN/GaN微波功率HEMT,外延材料利用金属有机物化学气相淀积技术生长.测试表明,该lmm栅宽器件栅长为0.8μm,输出电流密度达到1.16A/mm,跨导为241mS/mm,击穿电压＞80V,特征频率达到20GHz,最大振荡频率为28GHz.5.4GHz连续波测试下功率增益为14.2dB,输出功率达4.1W,脉冲条件测试下功率增益为14.4dB,输出功率为5.2W,两端口阻抗特性显示了在微波应用中的良好潜力.     

钝化前表面预处理对AlGaN/GaN HEMTs性能的影响

提出一种新的钝化技术--采用盐酸和氢氟酸混合预处理溶液(HF:HCI:H2O=1:4:20)对AIGaN/GaNHEMTs进行表面预处理后冉淀积Si3N4钝化,研究了新型钝化技术对AlGaN/GaN HEMTs性能的影响并分析其机理.与用常规方法钝化的器件相比,经过表面顶处理再钝化,成功地抑制了 AIGaN/GaN HEMTs肖特基特性的恶化,有效地增强抑制电流崩塌效应的能力,将GaN基HEMTs的输出功率密度提高到5.2W/mm,并展现良好的电学可靠性.通过X射线光电子谱(XPS)检测预处理前后的AIGaN表面,观察到经过预处理后的AIGaN表面氧元素的含量大幅度下降.表面氧元素的含量下降,能有效地降低表面态密度和表面电荷陷阱密度,被认为是提高AIGaN/GaN HEMTs性能的主要原因.     

钝化前表面预处理对AlGaN/GaN HEMTs性能的影响

提出一种新的钝化技术--采用盐酸和氢氟酸混合预处理溶液(HF:HCI:H2O=1:4:20)对AIGaN/GaNHEMTs进行表面预处理后冉淀积Si3N4钝化,研究了新型钝化技术对AlGaN/GaN HEMTs性能的影响并分析其机理.与用常规方法钝化的器件相比,经过表面顶处理再钝化,成功地抑制了 AIGaN/GaN HEMTs肖特基特性的恶化,有效地增强抑制电流崩塌效应的能力,将GaN基HEMTs的输出功率密度提高到5.2W/mm,并展现良好的电学可靠性.通过X射线光电子谱(XPS)检测预处理前后的AIGaN表面,观察到经过预处理后的AIGaN表面氧元素的含量大幅度下降.表面氧元素的含量下降,能有效地降低表面态密度和表面电荷陷阱密度,被认为是提高AIGaN/GaN HEMTs性能的主要原因.     

An AlGaN/GaN HEMT-Based Microstrip MMIC Process for Advanced Transceiver Design

A MMIC process in AlGaN/GaN technology for advanced transceiver design has been developed. The process is based on microstrip technology with a complete model library of passive elements and AlGaN/GaN HEMTs. The transistor technology in this process is suitable for both power and low noise design, demonstrated with a power density of 5 W/mm, and an ${rm NF}_{min}$ of 1.4 dB at $X$ -band. Process stability of subcircuits, complementary to power amplifiers and LNAs, in a transceiver system have been investigated. The results indicate that an all AlGaN/GaN MMIC transceiver is realizable using this technology.      

MOCVD-Grown AlGaN Buffer GaN HEMTs With V-Gates for Microwave Power Applications

We report the performance of AlGaN buffer GaN high-electron mobility transistors (HEMTs) grown by metal–organic chemical vapor deposition. GaN HEMTs on high-quality AlGaN buffer were grown on SiC substrates. The incorporation of an AlGaN buffer into the GaN HEMT significantly improves channel confinement and suppresses the short-channel effect. Advanced deep-recess V-gate structures were employed to optimize the device for better microwave power performance. With a 10-nm GaN channel layer sandwiched between the AlGaN barrier and buffer, excellent power performance was achieved. The output power density is 13.1 W/mm, and the associated power-added efficiency is 72% at 4-GHz frequency and 48-V drain bias. This power performance is comparable to the state-of-the-art GaN HEMTs grown on GaN buffers, indicating that the AlGaN buffer in our optimized device structure does not introduce any noticeable trapping.      

Power Performance of AlGaN/GaN HEMTs Grown on SiC by Ammonia-MBE at 4 and 10 GHz

In this letter, we report on the microwave power and efficiency performance of AlGaN/GaN high-electron mobility transistors (HEMTs) grown by ammonia molecular beam epitaxy (ammonia-MBE) on SiC substrates. At 4 GHz, an output power density of 11.1 W/mm with an associated power-added efficiency (PAE) of 63% was measured at V _ds = 48 V on passivated devices. At 10 GHz, an output power density of 11.2 W/mm with a PAE of 58% was achieved for V _ds = 48 V. These results are the highest reported power performance for AlGaN/GaN HEMTs grown by ammonia-MBE and the first reported for ammonia-MBE on SiC substrates.     

Influence of barrier thickness on the high-power performance ofAlGaN/GaN HEMTs

The dependence of current slump in AlGaN/GaN HEMTs on the thickness of the AlGaN barrier was observed. Power measurements on a 2×125×0.3 μm AlGaN/GaN HEMT made on Silicon Carbide (SiC) substrates with an AlGaN thickness of 10 nm gave a saturated output power of 1.23 W/mm at 8 GHz whereas a device with the same dimensions fabricated on samples with an AlGaN barrier of 20 nm gave a saturated output power of 2.65 W/mm at the same frequency. RF load line measurements clearly show the reduction of RF full channel current as compared to dc full channel current and the increase in the RF knee voltage compared to the dc knee voltage, with the effect being more pronounced in thin barrier samples. Passivation improved the large signal performance of these devices. A 1×150×0.3 μm transistor made on AlGaN(20 nm)/GaN structure gave a saturated output power of 10.7 W/mm (40% power added efficiency) at 10 GHz after passivation. This represents the state of the art microwave power density for AlGaN/GaN HEMTs. Heating of the transistors during high-power operation of these devices becomes the important factor in limiting their performance after passivation     

输出功率密度为2.23W/mm的X波段AlGaN/GaN功率HEMT器件

MOCVD技术在蓝宝石衬底上制备出具有高迁移率GaN沟道层的AlGaN/GaN HEMT材料.高迁移率GaN外延层的室温迁移率达741cm2/(V·s),相应背景电子浓度为1.52×1016cm-3;非有意掺杂高阻GaN缓冲层的室温电阻率超过108Ω·cm,相应的方块电阻超过1012Ω/□.50mm HEMT外延片平均方块电阻为440.9Ω/□,方块电阻均匀性优于96％.用此材料研制出了0.2μm栅长的X波段HEMT功率器件,40μm栅宽的器件跨导达到250mS/mm,特征频率fT为77GHz;0.8mm栅宽的器件电流密度达到1.07A/mm,8GHz时连续波输出功率为1.78W,相应功率密度为2.23W/mm,线性功率增益为13.3dB.     

4W/mm蓝宝石衬底AlGaN/GaN HEMT

报道了利用南京电子器件研究所生长的蓝宝石衬底AlGaN/GaN异质结材料制作的HEMT,器件功率输出密度达4W/mm。通过材料结构及生长条件的优化,利用MOCVD技术获得了二维电子气(2DEG)面密度为0.97×1013cm-2、迁移率为1000cm2/Vs的AlGaN/GaN异质结构材料,用此材料完成了栅长1μm、栅宽200μm AlGaN/GaN HEMT器件的研制。小信号测试表明器件的fT为17GHz、最高振荡频率fmax为40GHz;负载牵引测试得到2GHz下器件的饱和输出功率密度为4.04W/mm。     

C波段0.75mm AlGaN/GaN功率器件

研制并测试了以蓝宝石作衬底的10×75μm×0.8μm AlGaN/GaN微波器件,采用等离子增强气相化学沉积的方法生长了250nm的Si3N4形成钝化层,直流特性从0.56A/mm上升到0.66A/mm,跨导从158mS/mm增为170mS/mm,截止频率由10.7GHz增大到13.7GHz,同时在4GHz下,Vds＝25V, Vgs＝-2.5V,输出功率由0.90W增至1.79W,输出功率密度达到2.4W/mm. 钝化有效地改善了器件的输出特性,减小和消除了表面寄生栅对器件的影响.     

Comparison of GaN HEMTs on Diamond and SiC Substrates

The performance of AlGaN/GaN high-electron-mobility transistors (HEMTs) on diamond and SiC substrates is examined. We demonstrate GaN-on-diamond transistors with periphery WG = 250 mum, exhibiting ft = 27.4 GHz and yielding a power density of 2.79 W/mm at 10 GHz. Additionally, the temperature rise in similar devices on diamond and SiC substrates is reported. To the best of our knowledge, these represent the highest frequency of operation and first-reported thermal and X -band power measurements of GaN-on-diamond HEMTs.