Influence of growth conditions of oxide on electrical properties of AlGaN/GaN metal–insulator–semiconductor transistors

AlGaN/GaN metal–insulator–semiconductor high-electron-mobility transistors(MIS-HEMTs) on a silicon substrate were fabricated with silicon oxide as a gate dielectric by sputtering deposition and electron-beam(EB) evaporation. It was found that the oxide deposition method and conditions have great influences on the electrical properties of HEMTs. The low sputtering temperature or oxygen introduction at higher temperature results in a positive equivalent charge density at the oxide/AlGaN interface(Nequ), which induces a negative shift of threshold voltage and an increase in both sheet electron density(ns) and drain current density(ID). Contrarily, EB deposition makes a negative Nequ, resulting in reduced ns and ID. Besides, the maximum transconductance(gm-max) decreases and the off-state gate current density(I_G-off) increases for oxides at lower sputtering temperature compared with that at higher temperature, possibly due to a more serious sputter-induced damage and much larger Nequ at lower sputtering temperature. At high sputtering temperature, I_G-off decreases by two orders of magnitude compared to that without oxygen, which indicates that oxygen introduction and partial pressure depression of argon decreases the sputter-induced damage significantly. I_G-off for EB-evaporated samples is lower by orders of magnitude than that of sputtered ones, possibly attributed to the lower damage of EB evaporation to the barrier layer surface.     

Surface Barrier Models of ZnO

For a low surface barrier, the energy band, barrier height and width of the space charge region at the surface of relatively large grains of ZnO are presented analytically on condition that the electron distribution obeys the Boltzmann statistics. It is shown that the temperature in the space charge distribution factor has an important effect on the energy band, barrier height and width of the space charge region. The depletion approximation is a model in which the temperature in the space charge distribution factor is zero. Our results are better than the depletion approximation.     

RF and microwave characteristics of a 10 nm thick InGaN-channel gate recessed HEMT

A new depletion-mode gate recessed AlGaN/InGaN/GaN-high electron mobility transistor(HEMT)with 10 nm thickness of InGaN-channel is proposed.A growth of AlGaN over GaN leads to the formation of twodimensional electron gas(2DEG)at the heterointerface.High 2DEG density(ns)is achieved at the heterointerface due to a strain induced piezoelectric effect between AlGaN and GaN layers.The electrons are confined in the InGaN-channel without spilling over into the buffer layer,which also reduces the buffer leakage current.From the input transfer characteristics the threshold voltage is obtained as 4:5 V and the device conducts a current of 2 A/mm at a drain voltage of 10 V.The device also shows a maximum output current density of 1.8 A/mm at Vds of 3 V.The microwave characteristics like transconductance,cut-off frequency,max frequency of oscillation and Mason’s Unilateral Gain of the device are studied by AC small-signal analysis using a two-port network.The stability and power performance of the device are analyzed by the Smith chart and polar plots respectively.To our knowledge this proposed InGaN-channel HEMT structure is the first of its kind.     

Modeling of cylindrical surrounding gate MOSFETs including the fringing field effects

A physically based analytical model for surface potential and threshold voltage including the fringing gate capacitances in cylindrical surround gate(CSG) MOSFETs has been developed.Based on this a subthreshold drain current model has also been derived.This model first computes the charge induced in the drain/source region due to the fringing capacitances and considers an effective charge distribution in the cylindrically extended source/drain region for the development of a simple and compact model.The fringing gate capacitances taken into account are outer fringe capacitance,inner fringe capacitance,overlap capacitance,and sidewall capacitance.The model has been verified with the data extracted from 3D TCAD simulations of CSG MOSFETs and was found to be working satisfactorily.     

多栅指AlGaN/GaN HEMT器件自热效应研究

Self-heating in multi-finger AlGaN/GaN high-electron-mobility transistors(HEMTs) is investigated by measurements and modeling of device junction temperature under steady-state operation.Measurements are carried out using micro-Raman scattering to obtain the detailed and accurate temperature distribution of the device.The device peak temperature corresponds to the high field region at the drain side of gate edge.The channel temperature of the device is modeled using a combined electro-thermal model considering 2DEG transport characteristics and the Joule heating power distribution.The results reveal excellent correlation to the micro-Raman measurements, validating our model for the design of better cooled structures.Furthermore,the influence of layout design on the channel temperature of multi-finger AlGaN/GaN HEMTs is studied using the proposed electro-thermal model, allowing for device optimization.     

LDMOS器件热载流子退化特性测试中的电荷泵技术研究

A measuring technique based on the CP（charge pumping）method for hot-carrier degradation measurement of high voltage N-LDMOS is researched in depth.The impact of the special configuration on the CP spectrum and the gate voltage pulse frequency range which is suitable for high voltage N-LDMOS in CP measurements is investigated in detail.At the same time,the impacts of different reverse voltage applied on the source and drain electrodes and of the gate pulse shape on the CP curve change in N-LDMOS are also proposed and analyzed.The conclusions give guidance on measuring the density of interface states with experimental instructions and offer theoretic instructions for analyzing CP curves in high voltage N-LDMOS more accurately.     

增强型自对准源漏区AlN/GaN/AlN 氮极化金属绝缘半导体场效应晶体管的静态特性与短沟道效应的研究

This paper aims to simulate the I–V static characteristic of the enhancement-mode(E-mode) Npolar Ga N metal–insulator–semiconductor field effect transistor(MISFET) with self-aligned source/drain regions.Firstly, with SILVACO TCAD device simulation, the drain–source current as a function of the gate–source voltage is calculated and the dependence of the drain–source current on the drain–source voltage in the case of different gate–source voltages for the device with a 0.62 m gate length is investigated. Secondly, a comparison is made with the experimental report. Lastly, the transfer characteristic with different gate lengths and different buffer layers has been performed. The results show that the simulation is in accord with the experiment at the gate length of 0.62 m and the short channel effect becomes pronounced as gate length decreases. The E-mode will not be held below a100 nm gate length unless both transversal scaling and vertical scaling are being carried out simultaneously.     

A surface-potential-based model for AlGaN/AlN/GaN HEMT

A new surface-potential-based model for AlGaN/AlN/GaN high electron mobility transistor(HEMT) is proposed in this paper. Since the high polarization effects caused by AlN interlayer favorably influence the two dimensional electron gas(2DEG) and scattering mechanisms, we first add spontaneous and piezoelectric charge terms to the source equation of surface-potential, and a mobility model for AlGaN/AlN/GaN HEMT is rewritten. Compared with TCAD simulations, the DC characteristics of AlGaN/AlN/GaN HEMT are faithfully reproduced by the new model.     

多层浮栅FET pH传感单元阈值电压敏感模型分析和讨论

Research into new pH sensors fabricated by the standard CMOS process is currently a hot topic. The new pH sensing multi-floating gate field effect transistor is found to have a very large threshold voltage, which is different from the normal ion-sensitive field effect transistor. After analyzing all the interface layers of the structure, a new sensitive model based on the Gauss theorem and the charge neutrality principle is created in this paper. According to the model, the charge trapped on the multi-floating gate during the process and the thickness of the sensitive layer are the main causes of the large threshold voltage. From this model, it is also found that removing the charge on the multi-floating gate is an effective way to decrease the threshold voltage. The test results for three different standard pH buffer solutions show the correctness of the model and point the way to solve the large threshold problem.     

沟道电场分布对AlN/GaN HFETs极化库仑场散射的影响

Based on the measured capacitance–voltage(C–V) curves and current–voltage(I–V) curves for the prepared differently-sized Al N/Ga N heterostructure field-effect transistors(HFETs), the I–V characteristics of the Al N/Ga N HFETs were simulated using the quasi-two-dimensional(quasi-2D) model. By analyzing the variation in the electron mobility for the two-dimensional electron gas(2DEG) with the channel electric field, it is found that the different polarization charge distribution generated by the different channel electric field distribution can result in different polarization Coulomb field(PCF) scattering. The 2DEG electron mobility difference is mostly caused by the PCF scattering which can reach up to 899.6 cm2/(V s)(sample a), 1307.4 cm2/(V s)(sample b),1561.7 cm2/(V s)(sample c) and 678.1 cm2/(V s)(sample d), respectively. When the 2DEG sheet density is modulated by the drain–source bias, the electron mobility for samples a, b and c appear to peak with the variation of the 2DEG sheet density, but for sample d, no peak appears and the electron mobility rises with the increase in the2 DEG sheet density.     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.