板钛矿纳米TiO2微晶的热分析特性研究

对板钛纳米ＴｉＯ２微晶样品（ｎ－ＴｉＯ２）进行了差热分析（ＤＴＡ），发现其ＤＴＡ曲线上出现了Ａ、Ｂ两上吸热峰。通过对原始样品及其系列热处理样品进行Ｘ射线衍射（ＸＲＤ）实验，证实Ａ峰对应于物理或化学吸附的脱附过程，Ｂ峰完全对应于ｎ－ＴｉＯ２原始样品结构从板钛矿经锐钛矿向着金红石的一级相变；这一结构相变促成了纳米晶粒的生长。     

板钛矿相对TiO2纳米晶相转变的影响研究

本文以Ti(O BU) 4为前驱体 ,采用溶胶 凝胶工艺制备了TiO2 纳米晶。通过X 射线衍射 (XRD)分析证明了所制备的锐钛矿相TiO2 纳米晶中含有一些板钛矿相 ,发现在较低的热处理温度下 ,TiO2 纳米晶就发生了相转变 ,并且板钛矿 金红石相转变的过程比锐钛矿 金红石相转变过程快 ;同时锐钛矿相的晶胞常数c的变化似乎部分归因于有板钛矿相的存在。差热 热重同步分析 (DTA TGA)表明 ,在 36 0～ 5 0 0°C之间 ,可以观察到板钛矿 锐钛矿相转变的存在。最后对TiO2 纳米晶中含有的板钛矿相对锐钛矿 金红石相转变的作用机制进行了简要的分析。     

纳米二氧化钛粉体的多晶型制备及形成机理

本文分别以四氯化钛、硫酸钛和钛酸丁酯为前驱物,研究了水热条件下二氧化钛微晶粉体的结晶晶型、晶粒形貌和晶粒度.采用XRD和TEM等分析手段分别对产物的晶相和晶粒形貌进行表征.实验结果表明:对于200℃水热反应,以四氯化钛为前驱物,通过加入氢氧化钠调节反应介质酸碱度,当溶液pH值小于1时,有利于形成金红石型粉体;当溶液pH值大于3并小于7时,有利于形成锐钛矿型粉体;当溶液ph值大于7时,有利于形成板钛矿型粉体.以硫酸钛为前驱物,通过控制胶体制备工艺及反应温度,制备得到锐钛矿型和板钛矿型粉体.金红石型粉体呈长条柱状,锐钛矿呈菱形或双锥状,板钛矿呈板块状.经过较为系统的实验研究,获得了金红石、锐钛矿、板钛矿三种晶相的粉体,并可通过控制前驱物的种类及酸碱度和水热反应条件随意地制备出以上三种晶相中的单晶相粉体.从结晶学出发,解释了二氧化钛纳米粉体的结晶形貌,并从晶体生长过程及生长机理的角度讨论了二氧化钛同质变体的形成机理.     

板钛矿基纳米TiO2中板钛矿相和金红石相点阵参量研究

利用射线衍分析技术对板钛矿基纳米ＴｉＯ２系列榈中板钛矿和工石相的晶粒点阵参量进行了较细致的研究，并得了晶面间距、晶格常数、轴比、晶胞体积等参数及其相对于常且晶的变化情况，初步提示了晶粒微结构的尺寸效应。作首次在所制备的板钛矿基纳米ＴｉＯ２样品中发现板钛矿和金红石相晶粒存在着非单调、各向异性晶格变现象。     

纳米金红石型TiO2的低温制备

分别在中性，碱性和酸性环境下对钛酸四丁酯溶液进行水解以制备纳米二氧化钛。在中性和碱性环境下水解产物是非晶态的，当温度低于700℃煅烧只能得到脱钛矿型二氧化钛。在酸性环境下，通过调整酸和水的加入量将溶液在低温下（40－50℃）水解合成了从纯锐钛矿相到不同比例锐钛矿－金红石混晶相，再到纯金红石相的纳米二氧化钛，乙醇的加入促进凝胶的形成以及锐钛相向金红石相的转化。     

不同晶型纳米TiO2的溶剂热合成及其光催化活性研究

采用不同的醇溶剂,以六亚甲基四胺为沉淀剂,以TICl3为前驱体,通过溶剂热的方法控制合成出纳米级的锐钛矿型、金红石型和板钛矿型的二氧化钛.通过XRD、TEM、UV-Vis光谱和XPS能谱对其进行了表征,研究了醇的种类、六亚甲基四胺的量对二氧化钛相组成及光催化性能的影响.结果发现,以甲醇为溶剂,酸性条件有利于生成锐钛矿相,碱性条件有利于生成金红石相和板钛矿相.溶剂热条件下可以得到氮掺杂的TiO2-xNx.光催化降解甲基橙活性结果表明锐钛矿和板钛矿混晶具有最好的光催化活性.     

热处理对溶胶-凝胶TiO2薄膜的晶相转变和性能影响

以钛酸丁酯（TPOT）为有机醇盐前驱体，采用溶胶－凝胶技术制备了TiO2溶胶。为测量方便起见，分别制备了凝胶粉体和薄膜，并对样品进行了不同温度的热处理。X射线衍射（XRD）、椭偏仪和紫外－可见光谱（UV－vis)的测量表明：随热处理温度的升高，TiO2的结构由非晶到锐钛矿再到金红石相转变，400℃为锐钛矿相，600℃开始出现金红石相，800℃完全转变为金红石相；晶粒尺寸随热处理温度的升高而逐渐增大，锐钛矿结构的晶粒尺寸范围是2.5-5.5nm，金红石结构的晶粒尺寸范围是5.9-6.8nm；TiO2薄膜的折射率随热处理温度的升高而增大，同时薄膜厚度降低；禁带宽度随热处理温度的升高而增大，同时薄膜厚度降低；禁带宽度随热处理温度升高而变窄，锐钛矿结构的禁带宽度为3.45eV，而金红石结构的禁带宽度为3.30eV。     

直流电弧等离子体法制备TiO2纳米超细粉

采用直流电弧等离子体法直接制备了晶态的TiO2纳米超细粉,粉体中的晶粒既有锐钛矿结构,也有金红石结构;既有单晶结构的TiO2,也有多晶结构的TiO2.当热处理温度低于600℃时,粉体颗粒的长大较为缓慢,粒径在20nm以下;温度高于700℃时,颗粒迅速长大,锐钛矿向金红石结构的转变明显;当温度达到800℃时,样品转变为单晶结构的金红石型TiO2,颗粒大小在40-120nm之间.     

钛酸盐一维纳米材料向TiO2纳米材料的水热转化研究

采用强碱性水热处理法分别控制第一次水热反应为160℃和200℃,制备出一维纳米管和纳米棒2种形貌的产物,将其作为第二次水热反应的前驱体,考察了第二次水热体系中pH值和温度对TiO2纳米材料的晶相组成及其微观形貌的影响;采用XRD、TEM以及HRTEM对样品进行了分析.结果表明,当以纳米管为前驱体时,除在pH=0的体系中得到了以金红石相为主的单晶纳米棒外,在pH值为2、4和7的条件下均得到了单晶纯锐钛矿相TiO2纳米颗粒.当以纳米棒为前驱体时,在pH=0的体系中得到了金红石相与板钛矿相共存的纳米棒和纳米颗粒混合产物;在pH值为2、4和7的条件下均得到了纯锐钛矿相TiO2纳米棒;当二次水热温度低于180℃时,前驱体没有转化完全,所得产物为前驱体与锐钛矿相TiO2共存的纳米棒;当水热温度为180℃和210℃时,产物为纯锐钛矿相纳米棒.     

纳米晶Fe_2O_3和TiO_2结构相变的尺寸效应(英)

用DTA（差热分析）、TG（热重分析）和X射线衍射分析,研究了Fe2O3和TiO2纳米晶粒的结构相变．结果表明,对于Fe2O3纳米晶粒,只要没有发生γ→α转变,纳米晶粒就保持其原来的尺寸不变,而一旦发生了相变,晶粒的尺寸就会迅速长大．同样,对TiO2纳米晶粒,在从锐钛矿相→板钛矿相→金红石相的相变过程中,在相变发生以前,不管温度多高,纳米晶粒都保持其原来的尺寸不变,只要发生了相变,晶粒的尺寸就会迅速长大．对于纳米晶粒,依赖于晶粒尺寸的结构相变和依赖于结构相交的晶粒生长过程都是存在的．这是纳米晶的一种新的尺寸效应．     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.