溶胶-凝胶法制备外延Ba1-xSrxTiO3薄膜及其结构与性能研究

应用溶胶-凝胶技术在Pt/MgO(100)衬底上成功地制备了Ba0.65Sr0.35TiO3外延薄膜.XRD和SEM分析结果表明该薄膜在O2气氛中650℃热处理1h后,其(001)面是沿着Pt(100)和MgO(100)面外延取向生长的;薄膜表面均匀致密,厚度为260nm,平均晶粒大小为48.5nm.当测试频率为10kHz时,BST薄膜的介电常数和损耗因子分别为480和0.02.介电常数-温度关系测试结果表明sol-gel工艺制备的Ba0.65Sr0.35TiO3薄膜其居里温度在35℃左右,且在该温度下Ba0.65Sr0.35TiO3薄膜存在扩散铁电相变特征.当外加偏置电压为3V时,BST薄膜的漏电流密度为1.5×10-7A/cm2.该薄膜可作为制备新型非制冷红外焦平面阵列和先进非制冷红外热像仪的优选材料.     

利用Ba0.65Ru0.35TiO3缓冲层制备高热释电系数的Ba0.65Sr0.35TiO3薄膜

采用射频溅射,在Ba0.65Sr0.35TiO3(BST)薄膜和Pt/Ti/SiO2/Si衬底之间制备10 nm的Ba0.65Ru0.35RUO3 (BSR)缓冲层,研究了BSR缓冲层对BST薄膜结构和性能的影响.与没有BSR缓冲层的BST薄膜相比,BSR缓冲层可使BST薄膜呈高度a轴择优取向生长,改善了薄膜的介电常数,降低了薄膜的漏电流密度,使其热释电系数达到7.45×10-1 C cm-2 K-1.表明利用BSR缓冲层可以制备高热释电性能的BST薄膜.     

射频磁控溅射法制备（Ba0.7Sr0.3）TiO3铁电薄膜

采用射频磁控溅射法制备了用于非致冷红外焦平面阵列的（Ba0.7Sr0.3）TiO3（BST）铁电薄膜。研究了BST铁电薄膜的制备工艺,分析了BST铁电薄膜的晶体结构和微观形貌。测试了其介电特性,测得的相对介电常数－温度曲线表明制备的（Ba0.7Sr0.3）TiO3铁电薄膜的居里温度在室温附近,约30℃处。     

射频磁控溅射参数对Ba0.7Sr0.3TiO3薄膜结构和性能的影响

采用射频磁控溅射法在 Pt/TiO2/SiO2/Si(100) 衬底上制备了Ba0.7Sr0.3TiO3薄膜,研究了工作气压、衬底温度等溅射参数对Ba0.7Sr0.3TiO3薄膜结构和电学性质的影响.使用 XRD 分析了工作气压为 2Pa、衬底温度分别为 200 ℃、400 ℃、600℃(组a),以及衬底温度为600℃、工作气压分别为 1.5Pa、2.0Pa、2.5Pa、3.0Pa 和 5.0Pa (组b)两组薄膜的微结构,结果表明工作气压在 2.5Pa 以下、衬底温度为 600℃时沉积的薄膜具有较好的钙钛矿结构.在 1.5Pa 条件下溅射的薄膜具有明显的(111)择优取向.在2.5Pa时,Pt/Ba0.7Sr0.3TiO3/Pt电容有最优铁电性能,在外加4 V电压(电场为 80 kV/cm)下,剩余极化 (Pr) 和矫顽场(Ec)分别为 2.32 μC/cm2、21.1 kV/cm.     

溶胶–凝胶法制备BST薄膜的结晶特性研究

采用改进的溶胶–凝胶(sol-gel)工艺配制了(Ba0.65,Sr0.35)TiO3(BST)溶胶。利用旋转涂覆工艺将BST溶胶涂覆在SiO2/Si衬底上,在不同的热处理条件下制备出BST薄膜。XRD分析结果表明:制得的BST薄膜形成了单一钙钛矿结构;AFM测试结果表明,BST薄膜表面平整致密,无裂纹。表面均方根粗糙度为3~6nm,晶粒大小分布均匀,直径约为40~100nm。随着热处理温度的提高,BST薄膜的晶粒变大,表面粗糙度变大。     

(Ba0.5Sr0.5)TiO3/LaNiO3异质薄膜的介电调谐特性

用脉冲激光沉积工艺制备Ba0.5Sr0.5TiO3(简称BST)薄膜和Ba0.5Sr0.5TiO3/LaNiO3(简称BST/LNO)薄膜。在650℃原位退火10 min,获得了(100)和(110)择优取向生长的BST和BST/LNO薄膜,薄膜晶粒呈柱状结构,BST薄膜和BST/LNO异质结构薄膜的晶粒尺寸分别为150~200 nm和50~80 nm。在室温和1 MHz条件下,BST薄膜和BST/LNO异质结构薄膜的相对介电常数和介电调谐率分别达811和58.9%、986和60.1%;用LNO作底电极,可增益介电常数和介电调谐率。     

倒筒式射频溅射频偏压对Ba0.65Sr0.35TiO3热释电薄膜结构及性能的影响

采用倒筒式射频溅射方法,在Pt、Ti/SiO2/Si基片上制备了Ba0.65Sr0.35TiO3(简称BST)薄膜.研究了自偏压对BST薄膜结构及电学性能的影响.在较高自偏压下制备的BST薄膜具有高度的(100)择优取向,且结晶性好,表面平整,耐压能力强.在25℃时薄膜的热释电系数高达6.73×10-7C.cM-2.K-7.研究结果表明,利用倒筒式射频溅射方法适当提高自偏压,可以制备出热释电性能优良的BST薄膜.     

R.F.溅射Ba_(0.5)Sr_(0.5)TiO_3/RuO_2薄膜及其介电特性研究

用R.F.磁控溅射法在p—Si(100)衬底上沉积Ba0.5Sr0.5TiO3/RuO2异质结,BST薄膜的晶相和表面形貌用XRD和SEM分析,表明在衬底温度为550℃时,薄膜的结晶度高、表面粗糙、晶粒较大.电容器InGa/BST/RuO2的介电特性由ε-V特性和I—V特性描述.薄膜在零偏压下ε=230、tgδ≈0.03.低电场条件下,薄膜的漏电流随电压呈饱和特性,属电子跳跃传导,且通过改善薄膜的结晶度可减小该漏电流.高电场条件下,漏电流符合肖特基发射规律.     

外延Ba1-xSrxTiO3薄膜的Sol-Gel法制备及其电性能研究

以Ba(CH3COO)2,Sr(CH3COO)2和Ti(OC4H9)4为原料，以乙二醇甲醚为溶剂，冰乙酸为催化剂，应用溶胶－凝胶技术在Pt/MgO(100)衬底上成功地制备了外延生长B 0.65S0.35TiO3薄膜，XRD和SEM分析结果表明，该薄膜在O2气氛中650℃热处理1h后，其（001）面是沿着Pt(100)和MgO(100)面外延取向生长的，其平均晶粒大小为48．5nm，电性能测试结果表明，当测试频率为10kHz时，其介电常数和损耗因子分别为480和0．02，电滞回线测试结果表明，外延生长Ba0.65Sr0.35TiO3薄膜的剩余极化为2．8μC/cm^2其矫顽场为52kV/cm。     

射频磁控溅射法制备(Ba_(0.7)Sr_(0.3))TiO_3铁电薄膜

采用射频磁控溅射法制备了用于非致冷红外焦平面阵列的 ( Ba0 .7Sr0 .3) Ti O3( BST)铁电薄膜。研究了BST铁电薄膜的制备工艺 ,分析了 BST铁电薄膜的晶体结构和微观形貌。测试了其介电特性 ,测得的相对介电常数 -温度曲线表明制备的 ( Ba0 .7Sr0 .3) Ti O3铁电薄膜的居里温度在室温附近 ,约 3 0°C处。     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.     

GaAsSb/InAlAs PA DHBTs Grown by Production MBE

The epi material growth of GaAsSb based DHBTs with InAlAs emitters are investigated using a 4 × 100mm multi-wafer production Riber 49 MBE reactor fully equipped with real-time in-situ sensors including an absorption band edge spectroscope and an optical-based flux monitor. The state-of-the-art hole mobilities are obtained from 100nm thick carbon-doped GaAsSb. A Sb composition variation of less than ± 0.1 atomic percent across a 4 × 100mm platen configuration has been achieved. The large area InAlAs/GaAsSb/InP DHBT device demonstrates excellent DC characteristics,such as BVCEO＞6V and a DC current gain of 45 at 1kA/cm2 for an emitter size of 50μm × 50μm. The devices have a 40nm thick GaAsSb base with p-doping of 4. 5 × 1019cm-3 . Devices with an emitter size of 4μm × 30μm have a current gain variation less than 2% across the fully processed 100mm wafer. ft and fmax are over 50GHz,with a power efficiency of 50% ,which are comparable to standard power GaAs HBT results. These results demonstrate the potential application of GaAsSb/InP DHBT for power amplifiers and the feasibility of multi-wafer MBE for mass production of GaAsSb-based HBTs.     

Noise character analysis and the restraint of self-pulsation laser diodes

We calculate the Langevin noise sources of self-pulsation laser diodes, analyze the effects of active region noise and saturable-absorption region noise on the power fluctuation as well as period fluctuation, and propose a novel method to restrain the noise effects. A visible SIMULINK model is established to simulate the system, The results indicate that the effects of noise in absorption region can be ignored; that with the increase of DC injecting current, the noise effects enhance power jitter, and nevertheless, the period jitter is decreased; and that with external sinusoidal current modulating the self-pulsation laser diode, the noise-induced power jitter and period jitter can be suppressed greatly. This work is valuable for clock recovery in all-optical network.     

High-quality single-crystal CdSe nanoribbons and their optical properties

Large-scale synthesis of single-crystal CdSe nanoribbons is achieved by a modified thermal evaporation method, in which two-step-thermal-evaporation is used to control CdSe sources＇ evaporation. The synthesized CdSe nanoribbons are usually several micrometers in width, 50 nm in thickness, and tens to several hundred micrometers in length. Studies have shown that high-quality CdSe nanoribbons with regular shapes can be obtained by this method. Room-temperature photolumines-cence indicates that the lasing emission at 710 nm has been observed under optical pumping （266 nm） at power densities of 25-153 kW/cm^2. The full width half maximum （FWHM） of the lasing mode is 0.67 nm     

Propagation of hermite-cosh-gaussian beams passing through ABCD optical system with an annular aperture

By using the expansion of the aperture function into a finte sum of complex Gaussian functions, the corresponding analytical expressions of Hermite-cosh-Gaussian beams passing through annular apertured paraxially and symmetrically optical systems written in terms of ABCD matrix were derived, and they could reduce to the cases with squared aperture. In a similar way, the corresponding analytical expressions of cosh-Gaussian beams through annular apertured ABCD matrix were also given. The method could save more calculation time than that by using the diffraction integral formula directly.     

Influence of polarization extinction ratio on distributed polarization coupling detection

Distributed polarization coupling in polarization-maintaining fibers can be detected by using a white light Michelson interferometer. This technique usually requires that only one polarization mode is excited. However, in practical measurement, the injection polarization direction could not be exactly aligned to one of the principal axes of the PMF, so the influence of the polarization extinction ratio should be considered. Based on the polarization coupling theory, the influence of the incident polarization extinction on the measurement result is evaluated and analyzed, and a method for distributed polarization coupling detection is developed when both two orthogonal eigenmodes are excited.     

Call for Papers

正Communications—VLSI Researches and industries of telecommunications have been growing rapidly in the last 20 years and will keep their high growing pace in the next decade.The involved researches and developments cover mobile communications,highway and last-mile broadband communication,domain specific communications,and emerging D2D M2M communications.Radio communication steps into its