4H-SiC MESFET肖特基栅接触的界面参数提取

研究了界面态对4H-SiC MESFET的肖特基栅接触的影响.栅接触工艺主要采用Ti/Pt/Au蒸发,经过剥离后形成.基于热电子理论提出了一种参数提取方法,得到界面态密度和界面电容分别为4.386×1013cm-2·eV-1和8.394×10-6F/cm2,这与测量得到的器件端特性一致.     

退火气氛对Ge MOS电容电特性的影响

采用反应磁控溅射法在Ge衬底上制备了HfTiO高介电常数k栅介质薄膜,研究了不同气体(N2、NO、N2O)淀积后退火对Ge金属-氧化物-半导体(MOS)电容性能的影响.透射电子显微镜和电特性测量表明,湿N2退火能有效抑制界面层的生长,提高界面质量,改善栅极漏电流特性,从而得到最优的器件性能,即Al/HfTiO/n-Ge MOS电容的栅介质等效氧化物厚0.81 nm,k=34.5,带隙中央界面态密度为2.4×1011cm-2·eV-1,1 V栅偏压下的栅极漏电流为2.71×10-4A·cm-2.     

反应离子刻蚀氮化硅过程的损伤研究

针对反应离子刻蚀氮化硅过程中无图形60 nm栅氧的等离子体损伤问题进行了研究.采用接触电势差技术研究了反应刻蚀中电荷在硅片表面上的沉积,利用非接触式CV测试技术研究了Si/SiO2界面态的变化.研究表明,电荷沉积与Si/SiO2界面态密度增加有较好的对应关系,电荷沉积较多的区域具有更高的界面态密度.然而,电荷沉积量与界面态密度不成正比例.     

PDSOI nMOSFETs关态击穿特性

分别采用不同的背栅沟道注入剂量制成了部分耗尽绝缘体上硅浮体和H型栅体接触n型沟道器件.对这些器件的关态击穿特性进行了研究.当背栅沟道注入剂量从1.0×1013增加到1.3×1013cm-2,浮体n型沟道器件关态击穿电压由5.2升高到6.7V,而H型栅体接触n型沟道器件关态击穿电压从11.9降低到9V.通过测量寄生双极晶体管静态增益和漏体pn结击穿电压,对部分耗尽绝缘体上硅浮体和H型栅体接触n型沟道器件的击穿特性进行了定性解释和分析.     

中波碲镉汞/钝化层界面电学特性研究

HgCdTe表面/界面特性对器件性能具有重要的影响,表面/界面的状态主要依赖于表面处理和钝化工艺。采用Br2/CH3OH腐蚀液对液相外延(LPE)生长的中波HgCdTe薄膜进行表面处理后,使用Cd Te/Zn S复合钝化技术进行表面钝化,制备了相应的MIS器件并进行器件C-V测试。结果表明,HgCdTe/钝化层界面固定电荷极性为正,面密度为2.1×1011 cm-2,最低快界面态密度为1.43×1011 cm-2·e V-1,在10 V栅压极值下慢界面态密度为4.75×1011 cm-2,较低的快界面态密度体现出了CdTe/ZnS复合钝化技术的优越性。     

PDSOI nMOSFETs关态击穿特性

分别采用不同的背栅沟道注入剂量制成了部分耗尽绝缘体上硅浮体和H型栅体接触n型沟道器件.对这些器件的关态击穿特性进行了研究.当背栅沟道注入剂量从1.0×1013增加到1.3×1013cm-2,浮体n型沟道器件关态击穿电压由5.2升高到6.7V,而H型栅体接触n型沟道器件关态击穿电压从11.9降低到9V.通过测量寄生双极晶体管静态增益和漏体pn结击穿电压,对部分耗尽绝缘体上硅浮体和H型栅体接触n型沟道器件的击穿特性进行了定性解释和分析.     

埋氧离子注入对P型部分耗尽SOI电学与低频噪声的影响

针对抗辐照SOI PMOS器件的直流特性与低频噪声特性展开试验与理论研究,分析离子注入工艺对PMOS器件电学性能的影响,并预测其稳定性的变化。首先,对离子注入前后PMOS器件的阈值电压、迁移率和亚阈摆幅进行提取。测量结果表明:埋氧化层离子注入后,器件背栅阈值电压由-43.39 V变为-39.2 V,空穴有效迁移率由127.37 cm2/Vs降低为80.45 cm2/Vs,亚阈摆幅由1.35 V/dec增长为1.69 V/dec;结合背栅阈值电压与亚阈摆幅的变化,提取得到埋氧化层内电子陷阱与背栅界面态数量的变化。随后,分析器件沟道电流噪声功率谱密度随频率、沟道电流的变化,提取γ因子与平带电压噪声功率谱密度,由此计算得到背栅界面附近的缺陷态密度。基于电荷隧穿机制,提取离子注入前后埋氧化层内陷阱态随空间分布的变化。最后,基于迁移率随机涨落机制,提取得到离子注入前后PMOS器件的平均霍格因子由6.19×10-5增长为2.07×10-2,这表明离子注入后器件背栅界面本征电性能与应力稳定性将变差。     

金属/p-GaAs界面态对接触电阻作用机理的研究

本文针对大功率垂直腔面发射激光器(vertical cavity surface emitting laser, VCSEL)阵列热阻大、出光不均匀的问题,研究p-GaAs层欧姆接触电阻值的作用机理,降低欧姆接触串联电阻的方法,以提高VCSEL阵列出射光功率的均匀性。基于3种常用欧姆接触金属Ti/Au、Ni/Au、Ti/Al/Ti/Au,研究各层金属厚度和金属组合对与p型欧姆接触电阻的作用规律;结合等离子体表面处理工艺,改变金属/p-GaAs界面态,研究界面态对欧姆接触电阻的影响规律。实验对比分析得到金属Ti/Au结构电极欧姆接触的比接触电阻率最低,为3.25×10^-4 Ω·cm²;基于金半接触势垒模型,通过表面等离子体处理,界面势垒可降低12.6%(0.269 2 eV降至0.235 3 eV),等离子体轰击功率可调控金半界面的势垒和态密度。     

p-Si TFT栅绝缘层用SiNx薄膜界面特性的研究

以NH3和SiH4为反应源气体,在低温下采用射频等离子体增强化学气相沉积(RF-PECVD)法在多晶硅(p-Si)衬底上沉积了SiNx薄膜.系统地分析讨论了沉积温度、射频功率、反应源气体流量比对SiNx薄膜界面特性的影响.分析表明,沉积温度和射频功率主要是通过影响SiNx薄膜中的si/N比和H含量影响薄膜的界面特性,而NH3/SiH4流量比则主要通过影响薄膜中的H含量影响薄膜界面特性.实验制备的SiNx薄膜层中的固定电荷密度、可动离子密度、SiNx与p-si之间的界面态密度分别达到了1.7×1012/cm2、1.4×1012/cm2、3.5×1012/(eV·cm2),其界面特性达到了制备高质量p-si TFT栅绝缘层的性能要求.     

高阈值电压低界面态增强型Al2O3/GaN MIS-HEMT

采用高温热氧化栅极凹槽刻蚀工艺并结合高温氮气氛围退火技术,制备出了高阈值电压的硅基GaN增强型Al_2O_3/GaN金属-绝缘体-半导体高电子迁移率晶体管(MIS-HEMT)。采用高温热氧化栅极凹槽刻蚀工艺刻蚀AlGaN层,并在AlGaN/GaN界面处自动终止刻蚀,可有效控制刻蚀的精度并降低栅槽表面的粗糙度。同时,利用高温氮气退火技术能够修复Al_2O_3/GaN界面的界面陷阱,并降低Al_2O_3栅介质体缺陷,因此能够减少Al_2O_3/GaN界面的界面态密度并提升栅极击穿电压。采用这两项技术制备的硅基GaN增强型Al_2O_3/GaN MIS-HEMT具有较低的栅槽表面平均粗糙度(0.24 nm)、较高的阈值电压(4.9 V)和栅极击穿电压(14.5 V)以及较低的界面态密度(8.49×10¹¹ cm^-2)。     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.     

GaAsSb/InAlAs PA DHBTs Grown by Production MBE

The epi material growth of GaAsSb based DHBTs with InAlAs emitters are investigated using a 4 × 100mm multi-wafer production Riber 49 MBE reactor fully equipped with real-time in-situ sensors including an absorption band edge spectroscope and an optical-based flux monitor. The state-of-the-art hole mobilities are obtained from 100nm thick carbon-doped GaAsSb. A Sb composition variation of less than ± 0.1 atomic percent across a 4 × 100mm platen configuration has been achieved. The large area InAlAs/GaAsSb/InP DHBT device demonstrates excellent DC characteristics,such as BVCEO＞6V and a DC current gain of 45 at 1kA/cm2 for an emitter size of 50μm × 50μm. The devices have a 40nm thick GaAsSb base with p-doping of 4. 5 × 1019cm-3 . Devices with an emitter size of 4μm × 30μm have a current gain variation less than 2% across the fully processed 100mm wafer. ft and fmax are over 50GHz,with a power efficiency of 50% ,which are comparable to standard power GaAs HBT results. These results demonstrate the potential application of GaAsSb/InP DHBT for power amplifiers and the feasibility of multi-wafer MBE for mass production of GaAsSb-based HBTs.     

Influence of polarization extinction ratio on distributed polarization coupling detection

Distributed polarization coupling in polarization-maintaining fibers can be detected by using a white light Michelson interferometer. This technique usually requires that only one polarization mode is excited. However, in practical measurement, the injection polarization direction could not be exactly aligned to one of the principal axes of the PMF, so the influence of the polarization extinction ratio should be considered. Based on the polarization coupling theory, the influence of the incident polarization extinction on the measurement result is evaluated and analyzed, and a method for distributed polarization coupling detection is developed when both two orthogonal eigenmodes are excited.     

Noise character analysis and the restraint of self-pulsation laser diodes

We calculate the Langevin noise sources of self-pulsation laser diodes, analyze the effects of active region noise and saturable-absorption region noise on the power fluctuation as well as period fluctuation, and propose a novel method to restrain the noise effects. A visible SIMULINK model is established to simulate the system, The results indicate that the effects of noise in absorption region can be ignored; that with the increase of DC injecting current, the noise effects enhance power jitter, and nevertheless, the period jitter is decreased; and that with external sinusoidal current modulating the self-pulsation laser diode, the noise-induced power jitter and period jitter can be suppressed greatly. This work is valuable for clock recovery in all-optical network.     

High-quality single-crystal CdSe nanoribbons and their optical properties

Large-scale synthesis of single-crystal CdSe nanoribbons is achieved by a modified thermal evaporation method, in which two-step-thermal-evaporation is used to control CdSe sources＇ evaporation. The synthesized CdSe nanoribbons are usually several micrometers in width, 50 nm in thickness, and tens to several hundred micrometers in length. Studies have shown that high-quality CdSe nanoribbons with regular shapes can be obtained by this method. Room-temperature photolumines-cence indicates that the lasing emission at 710 nm has been observed under optical pumping （266 nm） at power densities of 25-153 kW/cm^2. The full width half maximum （FWHM） of the lasing mode is 0.67 nm     

Propagation of hermite-cosh-gaussian beams passing through ABCD optical system with an annular aperture

By using the expansion of the aperture function into a finte sum of complex Gaussian functions, the corresponding analytical expressions of Hermite-cosh-Gaussian beams passing through annular apertured paraxially and symmetrically optical systems written in terms of ABCD matrix were derived, and they could reduce to the cases with squared aperture. In a similar way, the corresponding analytical expressions of cosh-Gaussian beams through annular apertured ABCD matrix were also given. The method could save more calculation time than that by using the diffraction integral formula directly.     

中国建立EB级存储实验室,致力云计算应用(英文)

正With the support of 863 programs,Sugon Information Industry Co.,Ltd.,set up a dawning EB-class storage laboratory to address massive data storage requirements and largescale cloud computing demonstration applications.The Dawning EB-class cloud storage system adopts advanced fault-tolerant architecture,efficient data fault-tolerant algorithms with user authentication and data encryption policies to deal with the"lost""wrong"and"stolen"problems of data for ensuring the reliability and safety of the EB-class storage system in the public network application environments.The Dawning EB-class Storage Laboratory taking advan-