共查询到19条相似文献,搜索用时 328 毫秒
1.
2.
3.
交错反激变换器可将反激变换器的输出功率提高1倍。但反激变换器开关管关断电压尖峰大和变换器变换效率低的缺点没有得到改善。交错有源箝位反激变换器,克服了反激变换器的缺点,但开关管多,控制较为复杂。该文提出了一种新颖的带有箝位电容的交错反激变换器并详细分析了其工作原理。该变换器交错的结构和箝位电容的引入使该变换器克服了交错反激变换器和有源箝位反激变换器的主要缺点。具有结构简单,可靠性高,开关管关断电压尖峰小,功率等级较大,效率较高等特点。研制了一台600W的原理样机,并通过实验验证了理论分析的正确。 相似文献
4.
传统的有源箝位变换器存在输出电流脉动较大的缺点。文中利用磁集成技术、将电感和变压器的交变磁通正向耦合,来减小有源箝位变换器的输出电流脉动。文中提出了磁集成有源箝位正激变换器,并对其工作原理进行详细分析。通过将零纹波点设定在0.5占空比处,使得变换器同时得到最小的输出电流纹波和最低的原边开关管的电压应力。文中给出了集成磁件的设计公式以及原边电流脉动和输出电流脉动的表达式。最后通过2台100W磁集成和传统式的有源箝位正激变换器的实验对比,验证了理论分析的正确性。实验表明,与传统的变换器相比,磁集成有源箝位变换器具有更高的变换效率和更小的输出纹波。 相似文献
5.
输出纹波最小化有源箝位正激磁集成变换器 总被引:3,自引:1,他引:2
传统有源箝位变换器存在输出电流脉动较大的缺点。利用磁集成技术将电感和变压器的交变磁通正向耦合,以减小有源箝位变换器的输出电流脉动。该文提出磁集成有源箝位正激变换器,并对其工作原理进行分析。通过将零纹波点设定在0.5占空比处,使变换器同时得到最小输出电流纹波和最低原边开关管的电压应力。给出集成磁件的设计公式以及原边电流脉动和输出电流脉动的表达式。通过2台100 W磁集成和传统式的有源箝位正激变换器的实验对比,验证了理论分析的正确性。实验表明,与传统变换器相比,磁集成有源箝位变换器具有更高的变换效率和更小的输出纹波。 相似文献
6.
7.
对有源箝位正激变换器进行了数学分析,在此理论基础之上着重于研究有源箝位同步整流正激变换器中所出现的肖特基现象以及应用LM5025时变换器在设计时要注意的问题,辅以实际的物理样机加以论证,效率可达88%,实验效果比较满意。 相似文献
8.
有源箝位正反激变换器的小信号建模与分析 总被引:1,自引:0,他引:1
在考虑各种寄生参数的情况下,基于平均状态空间法建立了有源箝位正反激变换器连续导电模式下的小信号模型,以此得出变换器的开环传递函数,并给出了补偿网络设计原则和方法,通过Matlab仿真验证了其具有良好的动态性能和静态特性。根据理论分析设计了一台3.3V/30A试验样机,实验结果验证了理论的正确性。 相似文献
9.
本文简要介绍了有源箝位同步整流正激变换器的原理及主要参数的设计方法,给出了具体的设计公式和样机结果。经理论分析及样机验证,证明了有源箝位同步整流正激变换器是适合低压大电流开关电源的高效拓扑。 相似文献
10.
11.
在建立有源箝位变换器小信号模型的基础上,对PWM峰值电流控制进行了研究,得到了完整的峰值电流控制交流小信号数学模型。最后采用Orcad仿真软件对系统进行仿真,并通过实验论证了模型的可行性。 相似文献
12.
一族正反激组合式双向DC-DC变换器 总被引:8,自引:8,他引:8
提出了一族正反激双向DC-DC变换器。它采用正激和反激组合的形式,在变换器的一侧绕组串联,另一侧并联。这种结构的双向变换拓扑解决了电流型一电压型组合式拓扑的开关管电压尖峰问题和启动问题。正激和反激组合式的拓扑,减小了反激变压器传递的功率,而使一部分功率以正激形式传递,为其在较大功率场合的应用提供了拓扑基础。文章以有源箝位正反激双向变换器为例,详细分析了其工作原理,着重分析了开关时序问题和软开关实现问题,并推导了其稳态工作基本关系。通过构建试验样机平台,证明正反激双向DC-DC变换器理论分析的正确性。最后,给出了一族基于正反激原理的双向DC—DC变换器。 相似文献
13.
14.
Dakshina Murthy‐Bellur Marian K. Kazimierczuk 《International Journal of Circuit Theory and Applications》2011,39(8):849-864
The two‐switch flyback DC–DC converter is an extended version of the conventional single‐switch flyback converter. An additional switch and two clamping diodes serve as a simple, but an effective way to limit the switch overvoltages, which occur in the conventional single‐switch flyback converter due to the ringing of the resonant circuit formed by the transformer leakage inductance and the transistor output capacitance. The clamping diodes in the two‐switch flyback topology clamp the maximum voltage across each switch equal to the DC input voltage. This paper presents a detailed analysis and design procedure of the diode‐clamped two‐switch flyback converter operated in discontinuous‐conduction mode (DCM). A comparison of power losses of the two‐switch and the single‐switch flyback converters is given. The two‐switch flyback converter was bread‐boarded to validate the theoretical analysis. Experimental results from a 20‐V/30‐W, 100‐kHz laboratory prototype verified that the maximum switch voltage is limited to the DC input voltage. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
15.
16.
电力电子变换器机内辅助开关电源设计与实验 总被引:2,自引:0,他引:2
论述了峰值电流控制RCD钳位反激变换器的原理,并首次提出了RCD钳位等关键电路参数设计准则,设计并研制成功的15W 220V 50Hz AC/270V DC/ 15V DC(0.8A),-15V DC(0.15A), 5V DC(0.2A)机内辅助开关电源具有功率密度高,变换效率高,过载与短路能力强,可靠性高等优良的综合性能,在AC/AC,DC/AC,AC/DC、DC/DC等四类电力电子变换器中均具有重要应用价值。 相似文献
17.
Dakshina Murthy‐Bellur Marian K. Kazimierczuk 《International Journal of Circuit Theory and Applications》2011,39(11):1145-1160
The two‐switch flyback DC‐DC converter is an extended version of the conventional single‐switch flyback converter. An additional switch and two clamping diodes serve as a simple, but an effective way to limit the switch overvoltages, which occur in the conventional single‐switch flyback converter due to the ringing of the resonant circuit formed by the transformer leakage inductance and the transistor output capacitance. The clamping diodes in the two‐switch flyback topology clamp the maximum voltage across each switch equal to the DC input voltage. This paper presents a detailed steady‐state analysis and design procedure of the diode‐clamped two‐switch flyback converter operated in continuous‐conduction mode (CCM). The power loss in each component of the two‐switch flyback converter is compared with those of the single‐switch flyback converters with and without RCD clamp, and is presented in a tabular form. The two‐switch flyback converter was bread‐boarded to validate the theoretical analysis. Experimental results from a 10 V/30 W, 100 kHz laboratory prototype verified that the maximum switch voltage is limited to the DC input voltage. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
18.
Jung-Goo Cho Ju-Won Baek Chang-Yong Jeong Geun-Hie Rim 《Industry Applications, IEEE Transactions on》1999,35(1):15-20
A novel zero-voltage and zero-current-switching (ZVZCS) full-bridge pulsewidth modulation converter is presented to simplify the circuits of the previously presented ZVSCS converters. A simple auxiliary circuit, which consists of one small capacitor and two small diodes, is added in the secondary to provide ZVZCS conditions to primary switches, as well as to clamp secondary rectifier voltage. The additional clamp circuit for the secondary rectifier is not necessary. The auxiliary circuit includes neither lossy components nor additional active switches, which makes the proposed converter efficient and cost effective. The principle of operation, features, and design considerations are illustrated and verified on a 2.5 kW 100 kHz insulated-gate-bipolar-transistor-based experimental circuit 相似文献
19.
反激变换器原边漏感对半导体器件的影响较大,通过RCD箝位电路可以降低半导体器件的关断电压尖峰.分析了RCD箝位电路在反激变换器中的工作原理,并介绍了RCD各个参数的设计方法以及RCD箝位电路的损耗分析,实验验证了RCD各参数对反激变换器的影响. 相似文献