Inconel 690传热管GTAW对接焊接头组织及力学性能研究

对Inconel 690传热管材进行钨极气体保护焊(GTAW)对接焊,采用拉伸试验机、压扁试验机和光学显微镜测试和分析传热管焊接接头,同时利用ANSYS软件开展焊接接头在设计工况失压时的一次应力强度校核。研究结果表明:焊缝中心为树枝胞状晶,熔合线附近为粗大柱状晶。室温时接头的平均抗拉强度为619 MPa,平均屈服强度为292 MPa,350℃时接头平均抗拉强度为475 MPa,平均屈服强度为206 MPa,拉伸接头断裂从熔合区开始贯穿整个焊缝组织,呈塑性断裂。压扁试验和反向压扁试验结果表明管接头完好。通过ANSYS分析可知,设计工况下传热管接头350℃许用应力强度150 MPa限值可满足其一次应力强度要求,且裕量较大。     

某铁矿强磁尾矿反浮选回收试验研究

针对我国西部某铁矿强磁选尾矿进行了反浮选回收铁资源的试验研究, 探讨了pH值、抑制剂可溶性淀粉用量、阳离子捕收剂十二胺用量对浮选指标的影响。结果表明, 在矿浆pH=10、可溶性淀粉用量2 400 g/t、十二胺用量400 g/t条件下进行一粗一精(精选药剂用量减半)闭路反浮选, 可获得铁品位43.88%、回收率50.93%的铁精矿产品。     

Predictive process mapping for laser powder bed fusion: A review of existing analytical solutions

One of the main challenges in the laser powder bed fusion (LPBF) process is making dense and defect-free components. These porosity defects are dependent upon the melt pool geometry and the processing conditions. Power-velocity (PV) processing maps can aid in visualizing the effects of LPBF processing variables and mapping different defect regimes such as lack-of-fusion, under-melting, balling, and keyholing. This work presents an assessment of existing analytical equations and models that provide an estimate of the melt pool geometry as a function of material properties. The melt pool equations are then combined with defect criteria to provide a quick approximation of the PV processing maps for a variety of materials. Finally, the predictions of these processing maps are compared with experimental data from the literature. The predictive processing maps can be computed quickly and can be coupled with dimensionless numbers and high-throughput (HT) experiments for validation. The present work provides a boundary framework for designing the optimal processing parameters for new metals and alloys based on existing analytical solutions.     

蒸压建材生产过程中钢渣安定性处理与活性化利用

钢渣安定性处理过程常常造成胶凝活性的损失。为此，本文利用改性助剂消除钢渣水化过程中产生的氢氧化物并生成胶凝产物，在蒸压建材的生产过程中实现钢渣安定性处理和游离氧化物的活性化利用，并避免单独处置钢渣造成的活性物质损失。研究表明，8%秸秆灰和3%磷酸二氢铵作为复合助剂制备的尾矿-钢渣蒸压试块体积稳定，抗压强度达24.0MPa。通过对蒸压样品游离氧化物消解率、化学结合水量及热重、XRD分析，得出钢渣安定性处理与活性化利用机制：硅质材料与钢渣中f-CaO水化生成的Ca(OH)₂结合迅速生成对体系力学强度有益的水化硅酸钙，避免因大量Ca(OH)₂积累造成体积膨胀；磷酸盐中的NH₄⁺、H₂PO₄^-与f-MgO结合生成磷酸铵镁及其他低溶度积复盐类矿物，进而消除因f-MgO水化生成Mg(OH)₂造成体积膨胀的隐患。试样在180℃蒸压4h后，f-CaO及f-MgO消解率分别可达86.28%、89.73%。本文将为利用钢渣大比例取代水泥和石灰生产蒸压建筑材料提供理论基础，对于提高钢渣利用率、减少碳排放具有重要价值。     

大豆蛋白纳米纤维对铁纳米颗粒的稳态化作用

为明确大豆蛋白纳米纤维的结构形成和扩宽铁强化剂的食品工业应用，以大豆分离蛋白（soy protein isolate，SPI）为原料，通过5 h的酸热处理制备纳米纤维（soy protein isolate fibrils，Fib SPI），系统研究纤维形成前后蛋白结构的变化，并进一步制备铁纳米颗粒（iron nanoparticles，Fe NPs），探究Fib SPI对铁的稳态化作用。研究结果表明：在酸热处理过程中，SPI产生大量的β-折叠结构，其与硫磺素T结合，显示出增强的荧光强度；此外，7S组分先发生降解，利于纤维成核形成，随后11S逐渐被水解，促进纤维生长；同时水解产生大量的小肽组分，提高了产物的还原力。研究进一步利用Fib SPI递送铁纳米颗粒（Fe NPs），发现与原始SPI相比，铁纳米颗粒可在Fib SPI原位形成胶体稳定的铁-大豆蛋白纳米纤维复合物（Fe FibSPI），并以Fe（II）形式存在，其对乳液体系色泽及稳定性的影响较硫酸亚铁或氯化铁小。该研究可为构建新型植物基铁强化剂递送体系提供理论和方法指导。     

Analysis of suitability of TPP ash-slag waste as materials for hydrogen fuel storage

The current trends in energy were described, the main of which is the use of alternative energy sources, especially hydrogen. The most common methods of hydrogen accumulation were proposed: accumulation of compressed gaseous hydrogen in high-pressure tanks; accumulation of liquid hydrogen in cryogenic tanks; storing hydrogen in a chemically bound state; accumulation of gaseous hydrogen in carriers with a high specific surface area. Based on the combination of advantages and disadvantages, the most promising methods of accumulation were selected: storage of liquid hydrogen and storage of hydrogen in carriers with a high specific surface area. The main requirement for materials for hydrogen storage by these methods was revealed – a high specific surface area. Prospects for the development of waste-free low-emission technologies due to the recycling of secondary raw materials and the development of low-temperature technologies for the synthesis of functional and structural materials were substantiated. The applicability of large-scale ash and slag waste from coal-fired thermal power plants as a raw material for obtaining materials by low-temperature technologies was shown. The traditional ways of using ash and slag waste as a raw material, active additive and filler in the production of cements were described. Modern technologies for the production of innovative materials with a unique set of properties were presented, namely carbon nanotubes, silica aerogel and geopolymer materials. The prospect of using geopolymer matrices as a precursor for the synthesis of a number of materials was described; the most promising type of materials was selected – geopolymer foams, which are mainly used as sorbents for purifying liquids and gases or accumulating target products, as well as heat-insulating materials. The possibility of obtaining products of any shape and size on the basis of geopolymer matrices without high-temperature processing was shown. The special efficiency of the development of the technology of porous granules and powders obtained from a geopolymer precursor using various methods was substantiated. The obtained granules can be used in the following hydrogen storage technologies: direct accumulation of hydrogen in porous granules; creation of insulating layers for liquid hydrogen storage units.     

Designing amorphous formulations of polyphenols with naringin by spray-drying for enhanced solubility and permeability

Naringin (NAR), a major flavanone (FVA) glycoside, is a component of food mainly obtained from grapefruit. We used NAR as a food additive to improve the solubility and permeability of hydrophobic polyphenols used as supplements in the food industry. The spray-dried particles (SDPs) of NAR alone show an amorphous state with a glass transition temperature (T_g) at 93.2 °C. SDPs of hydrophobic polyphenols, such as flavone (FVO), quercetin (QCT), naringenin (NRG), and resveratrol (RVT) were prepared by adding varying amounts of NAR. All SDPs of hydrophobic polyphenols with added NAR were in an amorphous state with a single T_g, but SDPs of hydrophobic polyphenols without added NAR showed diffraction peaks derived from each crystal. The SDPs with NAR could keep an amorphous state after storage at a high humidity condition for one month, except for SDPs of RVT/NAR. SDPs with NAR enhanced the solubility of hydrophobic polyphenols, especially NRG solubility, which was enhanced more than 9 times compared to NRG crystal. The enhanced solubility resulted in the increased membrane permeability of NRG. The antioxidant effect of the hydrophobic NRG was also enhanced by the synergetic effect of NAR. The findings demonstrated that NAR could be used as a food additive to enhance the solubility and membrane permeability of hydrophobic polyphenols.     

The influence of FeNi nanoparticles on the microstructures and soft magnetic properties of FeSi soft magnetic composites

In this work, a new type of FeSi/FeNi soft magnetic powder core (SMPC) was successfully fabricated by coating FeNi nanoparticles on the surface of FeSi micrometer powder. The effects of different contents of FeNi nanoparticles on the micromorphology, internal structures, and soft magnetic properties of SMPCs were studied. The results show that FeNi nanoparticles adhere to the surface of FeSi powder, which can effectively fill the air gap between FeSi powder and is beneficial to the compaction of the powder cores during the pressing process. Thus, the density of the SMPCs is increased. Compared to FeSi SMPCs, the comprehensive soft magnetic properties of FeSi/FeNi SMPCs have been greatly improved. When adding 15 wt% FeNi nanoparticles, the SMPCs exhibit excellent magnetic properties with high effective permeability (increased by 43.8 %) and low core loss (decreased by 22.1 %). The high performance FeSi/FeNi SMPCs prepared in this work are expected to be widely used in power choke coils, uninterruptible power supplies, and boosts and inverter inductors.