A 400 MHz Low Noise Amplifier at Cryogenic Temperature for Superconductor Filter System

A cryogenic low noise amplifier （LNA） using Agilent high electron mobility transistor （HEMT） for 380 MHzto 480 MHz is designed and fabricated, and the excellent cryogenic performance in superconducting receiver front-end for communication system is achieved. A special input impedance matching topology is implemented to provide low noise figure （NF） and good input matching in this cryogenic LNA design. The measurement results show that the NF is within 0.25 dB from the minimum NF of a single transistor, the power gain is above 20 dB, the flatness is within 1 dB, and the maximum input return loss is lower than -20 dB in bandwidth.     

Ultra-wideband CMOS low noise amplifier

A two-stage ultra-wideband CMOS low noise amplifier (LNA) is proposed. The first stage is optimised for wideband input matching and low noise figure, while the second stage is optimised to extend the -3 dB bandwidth of the overall amplifier. The combination of stages can provide lower noise figure and wider bandwidth simultaneously over that of previously reported feedback-based CMOS amplifiers. The implemented LNA shows a peak gain of 13.5 dB, more than 8.5 dB of input return loss, and a noise figure of 2.5-7.4 dB over a -3 dB bandwidth from 2 to 9 GHz with DC power consumption of 25.2 mW.     

A wideband LNA employing gate-inductive-peaking and noise-canceling techniques in 0.18μm CMOS

正This paper presents a wideband low noise amplifier(LNA) for multi-standard radio applications.The low noise characteristic is achieved by the noise-canceling technique while the bandwidth is enhanced by gateinductive -peaking technique.High-frequency noise performance is consequently improved by the flattened gain over the entire operating frequency band.Fabricated in 0.18μm CMOS process,the LNA achieves 2.5 GHz of -3 dB bandwidth and 16 dB of gain.The gain variation is within±0.8 dB from 300 MHz to 2.2 GHz.The measured noise figure(NF) and average HP3 are 3.4 dB and -2 dBm,respectively.The proposed LNA occupies 0.39 mm2 core chip area.Operating at 1.8 V,the LNA drains a current of 11.7 mA.     

A 0.6-V Low Power UWB CMOS LNA

This paper presents the design of a low-power ultra-wideband low noise amplifier in 0.18-mum CMOS technology. The inductive degeneration is applied to the conventional distributed amplifier design to reduce the broadband noise figure under low power operation condition. A common-source amplifier is cascaded to the distributed amplifier to improve the gain at high frequency and extend the bandwidth. Operated at 0.6V, the integrated UWB CMOS LNA consumes 7mW. The measured gain of the LNA is 10dB with the bandwidth from 2.7 to 9.1GHz. The input and output return loss is more than 10dB. The noise figure of the LNA varies from 3.8 to 6.9dB, with the average noise figure of 4.65dB. The low power consumption of this work leads to the excellent figure of gain-bandwidth product (GBP) per milliwatt     

A low supply voltage SiGe LNA for ultra-wideband frontends

A low-power low-noise amplifier (LNA) for ultra-wideband (UWB) radio systems is presented. The microwave monolithic integrated circuit (MMIC) has been fabricated using a commercial 0.25-/spl mu/m silicon-germanium (SiGe) bipolar CMOS (BiCMOS) technology. The amplifier uses peaking and feedback techniques to optimize its gain, bandwidth and impedance matching. It operates from 3.4 to 6.9GHz, which corresponds with the low end of the available UWB radio spectrum. The LNA has a peak gain of 10dB and a noise figure less than 5dB over the entire bandwidth. The circuit consumes only 3.5mW using a 1-V supply voltage. A figure of merit (FoM) for LNAs considering bandwidth, gain, noise, power consumption, and technology is proposed. The realized LNA circuit is compared with other recently published low-power LNA designs and shows the highest reported FoM.     

3.6~4.7GHz低噪声放大器

以一种经典的窄带低噪声放大器结构为基础,分析级联放大器的S参数,通过优化元件参数,获得了一种在3.6~4.7 GH z范围内具有低输入回波损耗、低噪声系数的放大器。采用标准的0.18μm RF CM O S工艺进行了设计和实现。芯片面积为0.6 mm×1.5 mm。测试结果表明:在3.6~4.7 GH z的范围内,该宽带低噪声放大器输入回波损耗小于-14 dB;噪声系数小于2.8 dB,增益大于10 dB。在1.8 V电源下功耗约为45 mW。     

High‐Gain Wideband CMOS Low Noise Amplifier with Two‐Stage Cascode and Simplified Chebyshev Filter

An ultra‐wideband low‐noise amplifier is proposed with operation up to 8.2 GHz. The amplifier is fabricated with a 0.18‐μm CMOS process and adopts a two‐stage cascode architecture and a simplified Chebyshev filter for high gain, wide band, input‐impedance matching, and low noise. The gain of 19.2 dB and minimum noise figure of 3.3 dB are measured over 3.4 to 8.2 GHz while consuming 17.3 mW of power. The Proposed UWB LNA achieves a measured power‐gain bandwidth product of 399.4 GHz.     

A low-power and high-gain fully integrated CMOS LNA

In this paper, we present the design of a fully integrated CMOS low noise amplifier (LNA) with on-chip spiral inductors in 0.18 μm CMOS technology for 2.4 GHz frequency range. Using cascode configuration, lower power consumption with higher voltage and power gain are achieved. In this configuration, we managed to have a good trade off among low noise, high gain, and stability. Using common-gate (CG) configuration, we reduced the parasitic effects of C_gd and therefore alleviated the stability and linearity of the amplifier. This configuration provides more reverse isolation that is also important in LNA design. The LNA presented here offers a good noise performance. Complete simulation analysis of the circuit results in center frequency of 2.4 GHz, with 37.6 dB voltage gain, 2.3 dB noise figure (NF), 50 Ω input impedance, 450 MHz 3 dB power bandwidth, 11.2 dB power gain (S₂₁), high reverse isolation (S₁₂)<−60 dB, while dissipating 2.7 mW at 1.8 V power supply.     

Optimum Design for a Low Noise Amplifier in S-Band

An optimum design of a low noise amplifier (LNA) in S-band working at 2-4 GHz is described. Choosing FHC40LG high electronic mobility transistor (HEMT), the noise figure of the designed amplifier simulated by Microwave Office is no more than 1.5 dB, meanwhile the gain is no less than 20 dB in the given bandwidth. The simulated results agree with the performance of the transistor itself well in consideration of its own minimum noise figure (0.3 dB) and associated gain (15.5 dB). Simultaneously, the stability factor of the designed amplifier is no less than 1 in the given bandwidth.     

Optimum Design for a Low Noise Amplifier in S-Band

An optimum design of a low noise amplifier （LNA） in S-band working at 2-4 GHz is described. Choosing FHC40LG high electronic mobility transistor （HEMT）, the noise figure of the designed amplifier simulated by Microwave Office is no more than 1.5 dB, meanwhile the gain is no less than 20 dB in the given bandwidth. The simulated results agree with the performance of the transistor itself well in consideration of its own minimum noise figure （0.3 dB） and associated gain （15.5 dB）. Simultaneously, the stability factor of the designed amplifier is no less than 1 in the given bandwidth.     

Low-power programmable gain CMOS distributed LNA

A design methodology for low power MOS distributed amplifiers (DAs) is presented. The bias point of the MOS devices is optimized so that the DA can be used as a low-noise amplifier (LNA) in broadband applications. A prototype 9-mW LNA with programmable gain was implemented in a 0.18-/spl mu/m CMOS process. The LNA provides a flat gain, S/sub 21/, of 8 /spl plusmn/ 0.6dB from DC to 6.2 GHz, with an input impedance match, S/sub 11/, of -16 dB and an output impedance match, S/sub 22/, of -10 dB over the entire band. The 3-dB bandwidth of the distributed amplifier is 7GHz, the IIP3 is +3 dBm, and the noise figure ranges from 4.2 to 6.2 dB. The gain is programmable from -10 dB to +8 dB while gain flatness and matching are maintained.     

3～10GHz SiGe HBTs超宽带低噪声放大器的设计

根据UWB(Ultra-wideband)无线通信标准.提出了一款超宽带低噪声放大器并进行了设计.该放大器选用高性能的SiGe HBTs,同时采用并联和串联多重反馈的两级结构,以达到超宽频带、高增益、低噪声系数以及良好的输入输出匹配的目的.仿真结果表明,放大器在3-10 GHz带宽内,增益.S21高达21 dB,增益平坦度小于1.5 dB,噪声系数在2.4～3.3 dB之间.输入输出反射系数(S11和S22)均小于-9 dB,并且在整个频带内无条件稳定.所有结果表明该LNA性能良好.     

A full W-band low noise amplifier module for millimeter-wave applications

A full W-band Low Noise Amplifier (LNA) Module is designed and fabricated in this letter. A broadband transition is introduced in this module. The proposed transition is designed, optimized based on the results from numerical simulations. The results show that 1 dB bandwidth of the transition ranges from 61 to 117 GHz. For the purpose of verification, two transitions in back-to-back connection are measured. The results show that transmission loss is only about 0.9-1.7dB. This transition is used to interface integrated circuits to waveguide components. The characteristic of the LNA module is measured after assembly. It exhibits a broad bandwidth of 75 to 110 GHz , has a small signal gain above 21 dB. The noise figure is lower than 5dB throughout the entire W-band (below 3 dB from 89 to 95GHz) at a room temperature. The proposed LNA module exhibits potential for millimeter wave applications due to its high small signal gain, low noise, and low dc power consumption     

0.1～2.8GHz超宽带低噪声放大器的研制

选用噪声较小、增益较高且工作电流较低的放大管ATF55143,利用两种负反馈和宽带匹配技术,结合ADS软件的辅助设计,研制出宽带低噪声放大器。在0.1～2.8GHz范围内,其增益大于30dB,平坦度小于±1.3dB,噪声系数小于1.45dB,工作电流小于60mA,驻波比小于1.8。该放大器成本较低,体积较小,可应用于各种微波通讯领域。     

一种基于MBE差分外延技术的SiGe低噪声放大器

采用MBE差分外延生长SiGe HBT基区,等平面隔离,多晶硅注入、快速退火形成发射区等工艺,实现了SiGe器件的平面集成。基于上述工艺技术研制的SiGe低噪声放大器(LNA),获得了1.7 GHz的带宽,23 dB的增益和3.5 dB的噪声系数。     

A low power dual-band multi-mode RF front-end for GNSS applications

A CMOS dual-band multi-mode RF front-end for the global navigation satellite system receivers of all GPS,Bei-Dou,Galileo and Glonass systems is presented.It consists of a reconfigurable low noise amplifier(LNA),a broadband active balun,a high linearity mixer and a bandgap reference(BGR) circuit.The effect of the input parasitic capacitance on the input impedance of the inductively degenerated common source LNA is analyzed in detail.By using two different LC networks at the input port and the switched cap...     

2-GHz CMOS射频低噪声放大器的设计与测试

本文采用CMOS工艺,针对无线通信系统前端(Front-end)的低噪声放大器进行了分析、设计、仿真和测试.测试结果表明,该放大器工作在2.04-GHz的中心频率上,3dB带宽约为110MHz,功率增益为22dB,NF小于3.3dB.测试结果与仿真结果能够很好地吻合.     

用于无线局域网的双频段低噪声放大器

采用0.18μmCMOS工艺设计并制造了一款新型的应用于无线局域网的双频段低噪声放大器。设计中,通过切换输入电感和负载电感,来使电路分别工作在2.4GHz和5.2GHz频段。在1.8V的电源电压下,在2.4GHz和5.2GHz两个频段上,其增益分别达到了11.5dB和10.2dB,噪声系数分别是3dB和5.1dB。芯片总面积是0.9mm×0.65mm。     

A 0.18μm CMOS low noise amplifier using a current reuse technique for 3.1-10.6 GHz UWB receivers

A new,low complexity,ultra-wideband 3.1-10.6 GHz low noise amplifier(LNA),designed in a chartered 0.18μm RFCMOS technology,is presented.The ultra-wideband LNA consists of only two simple amplifiers with an inter-stage inductor connected.The first stage utilizing a resistive current reuse and dual inductive degeneration technique is used to attain a wideband input matching and low noise figure.A common source amplifier with an inductive peaking technique as the second stage achieves high flat gain and wide -3 dB bandwidth of the overall amplifier simultaneously.The implemented ultra-wideband LNA presents a maximum power gain of 15.6 dB,and a high reverse isolation of—45 dB,and good input/output return losses are better than -10 dB in the frequency range of 3.1-10.6 GHz.An excellent noise figure(NF) of 2.8-4.7 dB was obtained in the required band with a power dissipation of 14.1 mW under a supply voltage of 1.5 V.An input-referred third-order intercept point(IIP3) is -7.1 dBm at 6 GHz.The chip area,including testing pads,is only 0.8×0.9 mm2.     

一个应用于卫星导航接收机的低功耗可配置双频多模射频前端

本文给出了一个应用于GPS、北斗、伽利略和Glonass四种卫星导航接收机的高性能双频多模射频前端。该射频前端主要包括有可配置的低噪声放大器、宽带有源单转双电路、高线性度的混频器和带隙基准电路。详细分析了寄生电容对源极电感负反馈低噪声放大器输入匹配的影响,通过在输入端使用两个不同的LC匹配网络和输出端使用开关电容的方法使低噪声放大器可以工作在1.2GHz和1.5GHz频带。同时使用混联的有源单转双电路在较大的带宽下仍能获得较好的平衡度。另外,混频器采用MGTR技术在低功耗的条件下来获得较高的线性度,并不恶化电路的其他性能。测试结果表明：在1227.6MHz和1557.42MHz频率下,噪声系数分别为2.1dB和2.0dB,增益分别为33.9dB和33.8dB,输入1dB压缩点分别0dBm和1dBm,在1.8V电源电压下功耗为16mW。