256×1线列InGaAs短波红外焦平面的研究

利用分子束外延(MBE)方法生长的掺杂InGaAs吸收层PIN InP/InGaAs/InP双异质结外延材料,通过台面制作、硫化后覆盖聚酰亚胺钝化、电极生长等工艺,制作了台面构造的256×1正照射InGaAs探测器阵列。测试了器件的I-V特性与响应光谱,得出器件的暗电流Id、零偏压电阻R0、G因子;通过信号和噪声的测试,计算出了在278K时的平均峰值探测率为1.33×1012cmHz1/2W-1。256元InGaAs探测器阵列与CTIA结构L128读出电路相互连,经封装后成功制备256×1线列InGaAs短波红外焦平面,在室温(300K)时测得256元响应信号,其响应不均匀性为19.3%。     

128×1线列InGaAs短波红外焦平面的研究

报道了用分子束外延(MBE)方法生长的掺杂InGaAs吸收层PIN InP/InGaAs/InP双异质结外延材料,通过干法刻蚀和湿法腐蚀相结合制作台面、硫化和聚酰亚胺钝化、电极生长等工艺,制备了128×1台面正照射InGaAs探测器阵列.测试了器件的变温I-V、响应光谱和探测率,在278K时平均峰值探测率为1.03×1012cmHz1/2W-1.实现了128元InGaAs探测器阵列与CTIA结构L128读出电路相互连,经封装后,在室温(291K)时成功测出128元响应信号.焦平面响应的不均匀性为18.3%,并对不均匀性产生的原因进行了分析.     

正照射与背照射InGaAs探测器的性能对比研究

首先介绍了InGaAs台面探测器的研究进展,然后为了验证利用台面结制作背照射器件的可行性,利用分子束外延(MBE)方法生长的掺杂InGaAs吸收层PIN InP/InGaAs/InP双异质结外延材料,通过台面制作、钝化、电极生长、背面抛光等工艺,制备了8元台面InGaAs探测器,并测试了正照射和背照射时,器件的Ⅰ-Ⅴ、信号和响应光谱.测试结果表明,正照射和背照射情况下,器件的响应信号差别不大,正照射下器件的平均峰值探测率为4.1×1011 cm·Hz1/2·W-1,背照射下器件的平均峰值探测率为4.0×1011 cm·Hz1/2·W-1,但背照射情况下器件的响应光谱在短波方向有更好的截止.     

正、背照InGaAs探测器的性能对比研究

为了验证利用台面结制作背照射器件的可行性,利用分子束外延(MBE)方法生长的掺杂InGaAs吸收层PIN InP/InGaAs/InP双异质结外延材料,通过台面制作、钝化、电极生长、背面抛光等工艺,制备了8元台面InGaAs探测器,并测试了正照射和背照射时,器件的I-V、信号和响应光谱.测试结果表明,正照射和背照射情况下,器件的响应信号差别不大,正照射下器件的平均峰值探测率为4.13×1011cmHz1/2W-1,背照射下器件的平均峰值探测率为4×1011cmHz1/2W-1,但背照射情况下器件的响应光谱在短波方向有更好的截止.     

正照射与背照射InGaAs探测器的性能对比研究

首先介绍了InGaAs台面探测器的研究进展，然后为了验证利用台面结制作背照射器件的可行性，利用分子束外延(MBE)方法生长的掺杂InGaAs吸收层PIN InP／InGaAs／InP双异质结外延材料，通过台面制作、钝化、电极生长、背面抛光等工艺，制备了8元台面InGaAs探测器，并测试了正照射和背照射时，器件的I-V、信号和响应光谱。测试结果表明，正照射和背照射情况下，器件的响应信号差别不大，正照射下器件的平均峰值探测率为4．1×1011cm·Hz1/2·W-1，背照射下器件的平均峰值探测率为4．0×1011cm·Hz1/2·W-1，但背照射情况下器件的响应光谱在短波方向有更好的截止。     

两种钝化结构InGaAs红外探测器低频噪声的研究

低频噪声的测量和分析已成为红外探测器性能和可靠性评估的一种重要手段.制备了聚酰亚胺单层钝化和硫化后ZnS/聚酰亚胺双层钝化两种结构InGaAs探测器,测试了不同偏压或不同温度下器件的低频噪声谱,讨论了偏压和温度对InGaAs探测器低频噪声的影响.随着偏压的增加,噪声增大,拐点向低频方向移动,并且低频噪声随温度降低而减小.认为硫化后ZnS/聚酰亚胺双层钝化器件相对聚酰亚胺单层钝化器件相同偏压或温度下噪声较小,拐点低.因为硫化处理和ZnS层增强了钝化效果,器件的表面漏电流明显减小,因而大大降低了器件的低频噪声.     

LBIC技术研究InGaAs线列探测器串音及光敏感区

利用激光诱导电流技术研究了InGaAs台面探测器的相邻探测器间的串音和光敏感区。用分子束外延方法生长掺杂InGaAs的PIN InP/InGaAs/InP 外延材料，制备了256×1正照射台面InGaAs线列探测器。测试结果表明，InGaAs线列探测器相邻探测器间没有串音，虽然台面结构周围吸收层已被腐蚀，但因为少数载流子的侧向收集，扩大了有效光敏感区。     

正照射与背照射InGaAs探测器的性能对比研究

首先介绍了InGaAs台面探测器的研究进展，然后为了验证利用台面结制作背照射器件的可行性，利用分子束外延（MBE）方法生长的掺杂InGaAs吸收层PIN InP／InGaAs／InP双异质结外延材料，通过台面制作、钝化、电极生长、背面抛光等工艺，制备了8元台面InGaAs探测器，并测试了正照射和背照射时，器件的Ⅰ-Ⅴ、信号和响应光谱。测试结果表明，正照射和背照射情况下，器件的响应信号差别不大，正照射下器件的平均峰值探测率为4．1×10^11cm·Hz^1/2·W^-1，背照射下器件的平均峰值探测率为4．0×10^11cm·Hz^1/2·W^-1，但背照射情况下器件的响应光谱在短波方向有更好的截止。     

近红外256×1元InGaAs焦平面探测器无效像元研究

采用分子束外延方法生长的PIN型InP/InGaAs/InP双异质结材料制备了正照射256×1元近红外探测器,并与128×1奇偶两路读出电路互连,制备了近红外256×1元焦平面探测器.针对近红外InGaAs焦平面探测器中的无效像元问题,通过光学显微镜、扫描电镜和电学测试将无效像元进行分类,并分析了无效像元产生的原因.研...     

InGaAs台面探测器的AIN钝化研究

首次介绍了采用AlN介质薄膜为钝化层的InGaAs台面型探测器(λ=2.4 μm).探测器采用分子束外延(MBE)方法生长的原位掺杂的PIN In0.78Ga0.22As/In0.78Ga0.22As/InxGa1-xAs/InP 外延材料.由于台面型器件的裸露面积较大,特另q是台面的成形工艺所带来的侧面损伤,加大了光生载流子的表面复合,使器件的暗电流、噪声等性能急剧下降.采用新的AlN钝化工艺,制备了8元正照射台面InGaAs探测器,室温下(T=300 K)电压为-0.5 V时.探测器的暗电流(ID)约为9×10-8 A,优值因子(R0A)大于30 Ωcm2,通过与其他钝化工艺所制备的器件的性能进行分析对比得出:AlN能有效地改善器件的表面状态,减小表面复合,从而降低了暗电流,提高了探测器的性能.     

Technology innovation and process integrations for sub-100nm gate patterning

This paper presents a brief overview of the Applied Centura(R)DPS(R)system,configured with silicon etch DPS Ⅱ chamber, with emphasis on discussing tuning capability for CD uniformity control. It also presents the studies of etch process chemistry and film integration impact for an overall successful gate patterning development. Discussions will focus on resolutions to key issues, such as CD uniformity, line-edge roughness, and multilayer film etching integration.     

White organic light-emitting devices based on fac tris（2- phenylpyridine） iridium sensitized 5,6,11,12-tetraphenylnap -hthacene

We have fabricated the white organic light-emitting devices （WOLEDs） based on 4,4＇ -bis（2,2 -diphenyl vinyl）-1,1＇ - biphenyl （DPVBi） and phosphorescence sensitized 5,6,11,12,-tetraphenylnaphthacene （rubrene）. The device structure is ITO/2T-NATA （20 nm）/NPBX （20 nm）/CBP： x%Ir（ppy）3：0.5% rubrene （8 nm）/NPBX （5 nm）/DPVBi （30 nm）/Alq（30 nm）/LiF（0.5 nm）/A1. In the devices, DPVBi acts as a blue light-emitting layer, the rubrene is sensitized by a phosphorescent material, fac tris （2-phenylpyridine） iridium [Ir（ppy）3], acts as a yellow light-emitting layer, and N,N＇ -bis- （1-naphthyl）- N,N＇ -diphenyl -1, 1＇ -biphenyl-4,4＇ -diamine （NPBX） acts as a hole transporting and exciton blocker layer, respectively. When the concentration of Ir （PPY）3 is 6wt%, the maximum luminance is 24960 cd/m^2 at an applied voltage of 15 V, and the maximum luminous efficiency is 5.17 cd/A at an applied voltage of 8 V.     

Complete approach to automatic identification and subpixel center location for ellipse feature

To meet the need of automatic image features extraction with high precision in visual inspection, a complete approach to automatic identification and sub-pixel center location for similar-ellipse feature is proposed. In the method, the feature area is identified automatically based on the edge attribute, and the sub-pixel center location is accomplished with the leastsquare algorithm. It shows that the method is valid, practical, and has high precision by experiment. Meanwhile this method can meet the need of instrumentation of visual inspection because of easy realization and without man-machine interaction.     

小角度扩展相关性近似算法分析

本论文提出一种在多天线MIMO信道相关性建模中小角度扩展近似理论算法,并应用于分析MIMO系统性能。分析中分别对三种不同角能量分布情况下的空间相关性研发快速近似计算法,并同时提出双模(Bi-Modal)角能量分布情况下的近似运算。通过分析这些新方法的近似效率,可以得到计算简单、复杂度低、而且符合实际的MIMO相关信道矩阵,对系统级的快速高效计算法的研究和系统级的评估以及误差分析具有重要的意义。     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

A Versatile Mixed-Signal Pin Approach for Cost-Effective Test of Automotive ICs

Integrated circuits (ICs) intended for increasingly sophisticated automotive applications bring unique test demands. Advanced ICs for applications such as highly integrated automatic braking system (ABS) and airbag controllers combine high voltage digital channels, significant VI demands and precise timing capability. Along with continued missioncritical reliability concerns, the trend toward higher voltage operation and increased device integration requires specialized test capabilities able to extend across the wide operating ranges found in automotive applications. Among these capabilities, automotive test requirements increasingly dictate a need for a cost-effective versatile mixed-signal pin electronics with very high data rates reaching up to 50MHz with a voltage swing of-2 V to +28 V.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.     

Optical vibration and deviation measurement of rotating machine parts

It is of interest to get appropriate information about the dynamic behaviour of rotating machinery parts in service. This paper presents an approach of optical vibration and deviation measurement of such parts. Essential of this method is an image derotator combined with a high speed camera or a laser doppler vibrometer （LDV）.