Effects of upholstery materials on the burning behavior of real‐scale residential upholstered furniture mock‐ups

Fire spread and growth on real‐scale four cushion mock‐ups of residential upholstered furniture (RUF) were investigated with the goal of identifying whether changes in five classes of materials (barrier, flexible polyurethane foam, polyester fiber wrap, upholstery fabric, and sewing thread), referred to as factors, resulted in statistically significant changes in burning behavior. A fractional factorial experimental design plus practical considerations yielded a test matrix with 20 material combinations. Experiments were repeated a minimum of two times. Measurements included fire spread rates derived from video recordings and heat release rates (HRRs). A total of 13 experimental parameters (3 based on the videos and 10 on the HRR results), referred to as responses, characterized the measurements. Statistical analyses based on Main Effects Plots (main effects) and Block Plots (main effects and factor interactions) were used. The results showed that three of the factors resulted in statistically significant effects on varying numbers of the 13 responses. The Barrier and Fabric factors had the strongest main effects with roughly comparable magnitudes. Foam was statistically significant for fewer of the responses and its overall strength was weaker than for Barrier and Fabric. No statistically significant main effects were identified for Wrap or Thread. Multiple two‐term interactions between factors were identified as being statistically significant. The Barrier*Fabric interaction resulted in the highest number of and strongest statistically significant effects. The existence of two‐term interactions means that it will be necessary to consider their effects in approaches designed to predict the burning behavior of RUF.     

Reduced‐scale test to assess the effect of fire barriers on the flaming combustion of cored composites: An upholstery‐material case study

Herein, we describe a reduced‐scale test (“Cube” test), measuring the fire performance of specimens including a fire barrier (FB) and a flammable core material, which acts as the main fuel load. The specimen is intended to reproduce a cross‐section of a composite product where heat/mass transfer occurs primarily in a direction perpendicular to the FB. The Cube test procedure and benefits are discussed in this work by adopting residential upholstery furniture as an exemplary study. One flexible polyurethane foam, one polypropylene cover fabric, and 10 commercially available FBs were selected. They were used to compare the fire performance of FBs, measured in terms of peak of heat release rate, in the ASTM E1474‐14 standard test and the newly developed Cube test. Edge effects severely affected the performance of FBs in the ASTM E1474‐14 standard test but not in the Cube test. Furthermore, appropriate test conditions were determined in the Cube test to measure the so‐called “wetting point,” that is, the time and value of heat release rate measured when flammable liquid products were first observed on the bottom of the specimen. The relevance of the “wetting point” in terms of full‐scale fire performance and failure mechanism of FBs is discussed.     

基于自适应LS-SVM的柴油机废气再循环冷却控制系统设计

针对当前柴油机废气再循环冷却控制系统受到时滞问题影响,导致系统开度走势与设定走势不一致、废气再循环效果差的问题,提出基于自适应LS-SVM的柴油机废气再循环冷却控制系统;以AT89C51单片机40针作为电控单元核心部件,利用位置传感器向系统发送负载信号,利用温度传感器来传输信号并反馈至D/A转换器;在D/A转换器中,反馈信号以串行或并行方式进入寄存器,并在转换后输出电流电压,控制系统阀门在排气再循环时的开启;伺服泵采用冷却系统,为系统提供液压动力源;利用自适应LS-SVM原理计算柴油机废气再循环冷却控制目标边界值,在最小二乘支持向量机基础上,利用求解线性方程组进行优化,消除了控制误差;根据控制差的大小,调整控制系统的输出值;由试验结果可知,该系统开度走势与设定开度走势一致,且与设定开度误差为1开度,说明使用该系统具有良好稳态特性,有效克服了系统中时滞问题,废气再循环效果较好。     

Real-time organic aerosol chemical speciation in the indoor environment using extractive electrospray ionization mass spectrometry

Understanding the sources and composition of organic aerosol (OA) in indoor environments requires rapid measurements, since many emissions and processes have short timescales. However, real-time molecular-level OA measurements have not been reported indoors. Here, we present quantitative measurements, at a time resolution of five seconds, of molecular ions corresponding to diverse aerosol-phase species, by applying extractive electrospray ionization mass spectrometry (EESI-MS) to indoor air analysis for the first time, as part of the highly instrumented HOMEChem field study. We demonstrate how the complex spectra of EESI-MS are screened in order to extract chemical information and investigate the possibility of interference from gas-phase semivolatile species. During experiments that simulated the Thanksgiving US holiday meal preparation, EESI-MS quantified multiple species, including fatty acids, carbohydrates, siloxanes, and phthalates. Intercomparisons with Aerosol Mass Spectrometer (AMS) and Scanning Mobility Particle Sizer suggest that EESI-MS quantified a large fraction of OA. Comparisons with FIGAERO-CIMS shows similar signal levels and good correlation, with a range of 100 for the relative sensitivities. Comparisons with SV-TAG for phthalates and with SV-TAG and AMS for total siloxanes also show strong correlation. EESI-MS observations can be used with gas-phase measurements to identify co-emitted gas- and aerosol-phase species, and this is demonstrated using complementary gas-phase PTR-MS observations.     

提高加盖钢包自开率的研究与实践

首钢京唐300t钢包加盖后自开率明显下降，分析了加盖钢包自开率下降的机理，确定了主要原因是包衬温度升高后造成的液态渣回流。通过对引流砂的流动性、密度和渗钢性研究，设计了一种适用于加盖钢包的引流砂成分配比，并通过控制Al2O3和MgO含量，保证铬矿砂纯度。改进了钢包热修工艺，设计了针对加盖钢包的投砂操作和防钢渣回流措施。研究结果经推广使用后，钢包月不自开炉数由8～9炉降低至2炉以内，综合自开率达99.9%，双精炼工艺自开率达100%。     

微裂隙中水泥浆液渗滤效应的可视化试验研究

在微裂隙岩体注浆过程中,水泥浆液的渗滤效应对注浆效果的影响显著。自主研制了一套微裂隙注浆可视化试验系统,该系统由注浆系统、微裂隙模型以及监测系统3个部分组成,监测系统又分为显微监测系统和压力流量监测系统。当水泥浆液进入微裂隙模型后,利用显微监测系统对裂隙入口处的渗滤效应进行实时观测。利用压力流量监测系统对注浆试验过程中的注浆压力以及累计流量进行自动记录。运用自主设计的微裂隙注浆可视化试验系统,对微裂隙中的水泥浆液渗滤过程进行试验研究。采用3种水泥浆材(超细水泥Ⅰ、超细水泥Ⅱ和普通水泥),研究在注浆压力2.0 MPa、水灰比1.0的条件下,不同水泥颗粒粒径大小在不同裂隙开度下的浆液渗滤效应。通过试验发现,当裂隙开度较小时,在裂隙入口处形成了完整的半圆拱形滤饼;随着裂隙开度的增加,在裂隙入口处形成断续分布状滤饼;当裂隙开度增加到无渗滤发生时,裂隙入口处仅残留少量水泥颗粒附着物。通过试验获得了3种水泥的最小可注入裂隙开度大小b min和最小无渗滤裂隙开度大小b crit:超细水泥Ⅰ的b min和b crit分别为80和280μm;超细水泥Ⅱ的b min和b crit分别为100和300μm;普通水泥的b min和b crit分别为140和310μm。研究结果发现水泥粒径的减小对最小可注入裂隙开度大小的影响较大,但对最小无渗滤裂隙开度大小的影响较小。结合渗滤趋势k值,发现随着水泥粒径的减小,相应的k min和k crit值会随之增加,水泥浆液更容易在裂隙入口处发生渗滤,这是因为超细水泥比表面积更大,水泥颗粒间易发生团聚。     

Physical and thermal properties of l‐lactide/ϵ‐caprolactone copolymers: the role of microstructural design

Understanding the underlying role of microstructural design in polymers allows for the manipulation and control of properties for a wide range of specific applications. As such, this work focuses on the study of microstructure–property relationships in l‐ lactide/?‐caprolactone (LL/CL) copolymers. One‐step and two‐step bulk ring‐opening polymerization (ROP) procedures were employed to synthesize LL/CL copolymers of various compositions and chain microstructures. In the one‐step procedure, LL and CL were simultaneously copolymerized to yield P(LL‐stat‐CL) statistical copolymers. In the two‐step procedure, poly(l‐ lactide) (PLL) and poly(?‐caprolactone) (PCL) prepolymers were synthesized in the first step before CL and LL respectively were added in the second step to yield P[LL‐b‐(CL‐stat‐LL)‐b‐LL] and P[CL‐b‐(LL‐stat‐CL)‐b‐CL] block copolymers as the final products. The findings reveal that, in addition to the copolymerization procedure employed, the length and type of the prepolymer play important roles in determining the chain microstructure and thereby the overall properties of the final copolymer. Moreover, control over the degree of crystallinity and the type of crystalline domains, which is controlled during the polymer chemistry process, heavily influences the physical and mechanical properties of the final polymer. In summary, this work describes an interesting approach to the microstructural design of biodegradable copolymers of LL and CL for potential use in biomedical applications. © 2019 Society of Chemical Industry     

基于CAN总线的多通道开度阀控制系统的设计

针对现有电动阀门控制系统可嵌入性差的问题，设计了一种基于CAN总线的网络化、多通道、开度型阀门嵌入式控制系统。其中，上位机主要用于下达各阀门开度等控制指令并同时监测其工作状态，而下位机采用双MCU架构，主MCU用于控制各阀门的开度大小，从MCU负责采集开度反馈电流以实现闭环控制。下位机采用了模糊PID算法进行控制参数的动态整定，可满足阀门在不同工况下的控制精度要求，并通过OLED屏显示各通道阀门的实际开度值。实验表明,该控制系统运行稳定，能实现对多通道开度阀的精准控制，控制精度在0.6%以内，并支持远程上位机控制和现地控制等多种工作模式。     

Copy-move forgery detection of duplicated objects using accurate PCET moments and morphological operators

This paper presents a new method for copy-move forgery detection of duplicated objects. A bounding rectangle is drawn around the detected object to form a sub-image. Morphological operator is used to remove the unnecessary small objects. Highly accurate polar complex exponential transform moments are used as features for the detected objects. Euclidian distance and correlation coefficient between the feature vectors are calculated and used for searching the similar objects. A set of 20 forged images with duplicated objects is carefully selected from previously published works. Additional 80 non-forged images are edited by the authors and forged by duplicating different kinds of objects. Numerical simulation is performed where the results show that the proposed method successfully detect different kinds of duplicated objects. The proposed method is much faster than the previously existing methods. Also, it exhibits high robustness to various attacks such as additive white Gaussian noise, JPEG compression, rotation, and scaling.     

操作窗口对排风柜污染物控制效果影响的实验研究

为提升排风柜的控污能力,在排风柜性能测试实验台上,采用示踪气体测试法和正交试验法,研究了操作窗口竖直开度、水平开度、面风速和操作窗口位置对排风柜前呼吸区污染物控制效果的影响。极差分析和方差分析结果表明:各因素对呼吸区污染物控制效果影响的强弱顺序依次为竖直开度、水平开度、面风速、操作窗口位置;操作窗口水平开度、竖直开度增大,排风柜对呼吸区的污染物控制效果减弱;面风速增大,控制效果增强;水平开度与竖直开度对控制浓度的影响存在较大的相关性,这2个因素对控制浓度的影响仅在另一因素达到一定水平后才能体现。