850nm氧化物限制型VCSEL的温度特性

采用热封闭系统对850nm氧化物限制型VCSEL的温度特性进行了研究.实验证实该器件在80℃仍能正常工作,在20～80℃的温度区间内,器件的斜率效率由0.3mW/mA降到0.2mW/mA.根据阈值电流的温度依赖性得出T0=350K,器件的基模红移为0.11nm/mW,实验确定其热阻为2.02℃/mW.     

适合低成本封装的1310 nm FP半导体激光器芯片

以太无源光网络(EPON)技术应用广泛,但是要求器件的出纤光功率较高.采用球透镜结合窄发散角芯片的封装方式逐渐成为主流.在有源区为基于AlGaInAs材料体系脊波导结构的1 310 nm法布里-珀罗(FP)半导体激光器中加入模式扩展结构,成功研制出温度特性良好、高效率、窄远场发散角的芯片.室温下芯片的阈值电流与无扩展波导结构的芯片相当,均为10 mA量级;效率达到0.6 mW/mA;远场发散角快轴为23°,慢轴为13°;85℃的阈值电流为20 mA,效率为0.55 mW/mA.该芯片可以使用低成本的晶体管外形(TO)封装技术制成,满足EPON标准的器件.     

垂直腔面发射激光器制作新工艺

采用一种新工艺制作了垂直腔面发射激光器(VCSEL),即用开环分布孔取代以往的环形沟道作为氧化物限制技术的注入窗口。因开环分布孔间形成多个桥,为电注入提供了天然的桥状通道,解决了电极过沟断线问题。这种新结构器件的输出功率约为以往结构器件的1.34倍。在20℃~80℃范围内,对器件的输出功率、阈值电流及波长漂移性进行了研究。60℃时最大输出光功率可达到6 mW。激射波长随温度升高呈线性变化,且向长波方向移动,速率为0.06 nm/℃。由实验结果计算出器件的热阻为1.96℃/mW。     

阴极缓冲层对m-MTDATA/BAlq有机紫外光探测器性能的影响

制备了有机紫外光探测器(OUV-PD),器件结构为I TO/m-MTDATA(30nm)/m-MTDATA:BAlq(40～60nm,1∶1)/BAlq(40nm)/LiF(1nm)/Al(100nm),并研究了施加Liq、TPBi、Bphen和Zn(4-MeBTZ)₂为阴极缓冲层时对器件性 能的影响。实验结果表明,OUV-PD光响应与阴极缓冲层厚度和电子传输性能紧密相关,在 1.05mW/cm²的波长为365nm UV光照射下,响应度最大值分别达到218mA/W、247mA/W、305mA/W 和283mA/W。     

电流限制性能好的双沟平面隐埋异质结激光器

本文报导新近研制的1.3μm InGaAsP/InP双沟平面隐埋异质结(DC-PBH)激光器,在室温下测量阈值电流的最小值为15mA,最大输出功率可大于40mW,外部微分量子效率(单面输出)为35％。器件的温度性能好,特征温度T_0为70～80K,最高连续工作温度可达100℃     

双沟道平面掩埋异质结激光器(DC—PBHLD)的研制工作取得新进展

武汉电信器件公司研制的1.3μm双沟道平面掩埋异质结激光器最近取得新的进展;1.5μmDC—PBHLD也取得初步试验成果。 1.3μmDC—PBHLD,20℃阈值电流最低可达13mA;光功率输出一般为10mW;温度在20～70℃时△I/△T一般可达0.7mA/℃;其中质量较好的LD温度为70℃时线性输出功率     

高斜效率高功率850nm氧化限制型垂直腔面发射激光器

报道了MOCVD生长的高性能850nm氧化限制型垂直腔面发射激光器．研制出的氧化直径为9μm的激光器25℃时的斜效率和阈值电流分别为0．82mW／mA和2．59mA，激光器在23mA时输出16mW最大光功率．氧化直径为5μm的激光器25℃时的最小阈值电流为570μA，其最大饱和光功率为5．5mW．     

High-Power Distributed Feedback Laser Diodes Emitting at 820nm

通过将二级光栅直接刻在脊形波导AlGaInAs/AlGaAs DFB激光器的无铝光波导层上,实现了波长约为820nm,单面功率为30mW的单纵模激光器.由于采用无铝光栅,保证了二次外延质量,从而得到较好的器件性能.激光器的阈值电流为57mA,斜率效率约为0.32mW/mA.     

激射波长为820nm的大功率分布反馈激光器

通过将二级光栅直接刻在脊形波导AlGaInAs/AlGaAs DFB激光器的无铝光波导层上,实现了波长约为820nm,单面功率为30mW的单纵模激光器.由于采用无铝光栅,保证了二次外延质量,从而得到较好的器件性能.激光器的阈值电流为57mA,斜率效率约为0.32mW/mA.     

高斜效率高功率850nm氧化限制型垂直腔面发射激光器

报道了MOCVD生长的高性能850nm氧化限制型垂直腔面发射激光器.研制出的氧化直径为9μm的激光器25℃时的斜效率和阈值电流分别为0.82mW/mA和2.59mA,激光器在23mA时输出16mW最大光功率.氧化直径为5μm的激光器25℃时的最小阈值电流为570μA,其最大饱和光功率为5.5mW.     

Technology innovation and process integrations for sub-100nm gate patterning

This paper presents a brief overview of the Applied Centura(R)DPS(R)system,configured with silicon etch DPS Ⅱ chamber, with emphasis on discussing tuning capability for CD uniformity control. It also presents the studies of etch process chemistry and film integration impact for an overall successful gate patterning development. Discussions will focus on resolutions to key issues, such as CD uniformity, line-edge roughness, and multilayer film etching integration.     

White organic light-emitting devices based on fac tris（2- phenylpyridine） iridium sensitized 5,6,11,12-tetraphenylnap -hthacene

We have fabricated the white organic light-emitting devices （WOLEDs） based on 4,4＇ -bis（2,2 -diphenyl vinyl）-1,1＇ - biphenyl （DPVBi） and phosphorescence sensitized 5,6,11,12,-tetraphenylnaphthacene （rubrene）. The device structure is ITO/2T-NATA （20 nm）/NPBX （20 nm）/CBP： x%Ir（ppy）3：0.5% rubrene （8 nm）/NPBX （5 nm）/DPVBi （30 nm）/Alq（30 nm）/LiF（0.5 nm）/A1. In the devices, DPVBi acts as a blue light-emitting layer, the rubrene is sensitized by a phosphorescent material, fac tris （2-phenylpyridine） iridium [Ir（ppy）3], acts as a yellow light-emitting layer, and N,N＇ -bis- （1-naphthyl）- N,N＇ -diphenyl -1, 1＇ -biphenyl-4,4＇ -diamine （NPBX） acts as a hole transporting and exciton blocker layer, respectively. When the concentration of Ir （PPY）3 is 6wt%, the maximum luminance is 24960 cd/m^2 at an applied voltage of 15 V, and the maximum luminous efficiency is 5.17 cd/A at an applied voltage of 8 V.     

Complete approach to automatic identification and subpixel center location for ellipse feature

To meet the need of automatic image features extraction with high precision in visual inspection, a complete approach to automatic identification and sub-pixel center location for similar-ellipse feature is proposed. In the method, the feature area is identified automatically based on the edge attribute, and the sub-pixel center location is accomplished with the leastsquare algorithm. It shows that the method is valid, practical, and has high precision by experiment. Meanwhile this method can meet the need of instrumentation of visual inspection because of easy realization and without man-machine interaction.     

小角度扩展相关性近似算法分析

本论文提出一种在多天线MIMO信道相关性建模中小角度扩展近似理论算法,并应用于分析MIMO系统性能。分析中分别对三种不同角能量分布情况下的空间相关性研发快速近似计算法,并同时提出双模(Bi-Modal)角能量分布情况下的近似运算。通过分析这些新方法的近似效率,可以得到计算简单、复杂度低、而且符合实际的MIMO相关信道矩阵,对系统级的快速高效计算法的研究和系统级的评估以及误差分析具有重要的意义。     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

A Versatile Mixed-Signal Pin Approach for Cost-Effective Test of Automotive ICs

Integrated circuits (ICs) intended for increasingly sophisticated automotive applications bring unique test demands. Advanced ICs for applications such as highly integrated automatic braking system (ABS) and airbag controllers combine high voltage digital channels, significant VI demands and precise timing capability. Along with continued missioncritical reliability concerns, the trend toward higher voltage operation and increased device integration requires specialized test capabilities able to extend across the wide operating ranges found in automotive applications. Among these capabilities, automotive test requirements increasingly dictate a need for a cost-effective versatile mixed-signal pin electronics with very high data rates reaching up to 50MHz with a voltage swing of-2 V to +28 V.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.     

Optical vibration and deviation measurement of rotating machine parts

It is of interest to get appropriate information about the dynamic behaviour of rotating machinery parts in service. This paper presents an approach of optical vibration and deviation measurement of such parts. Essential of this method is an image derotator combined with a high speed camera or a laser doppler vibrometer （LDV）.