退火温度对铁电薄膜钛酸锶钡的影响

用醋酸盐和钛酸酯为原料，采用改进的Sol—gel工艺在Pt／Ti／SiO2／Si基片上制备出Ba0.6Sr0.4TiO3(BST)铁电薄膜，然后进一步对薄膜进行退火实验：对(110)方向生长BST薄膜在550～750℃进行恒温退火。X射线衍射分析表明：退火温度在650℃以上时，BST薄膜转变为较为完整的ABO3型钙钛矿晶体结构，更高的退火温度将提高晶体的取向度。     

退火工艺对钛酸锶钡薄膜结构的影响

采用射频磁控溅射在Pt/Ti/SiO2/Si(100)衬底上制备Ba0.6Sr0.4TiO3(BST)铁电薄膜,在500~750℃之间对薄膜快速退火。XRD分析表明:500℃时BST薄膜开始晶化为ABO3型钙钛矿结构,温度越高结晶越完整,晶粒越大。理论计算表明,薄膜在低温退火后无择优取向,高温退火后在(111)、(210)晶面有择优取向。退火气氛、保温时间、循环次数等因素对薄膜晶粒大小无明显影响,但对表面粗糙度和结晶程度影响较大。     

磁控溅射法制备BST铁电薄膜的实验研究

采用射频磁控溅射法在Si和Pt/TiOx/SiO2/Si衬底上沉积了(Ba0.65Sr0.35)TiO3铁电薄膜,研究了BST铁电薄膜微观结构和介电性能。实验结果表明:衬底温度在550℃,工作气压为2.0 Pa的溅射条件下沉积的BST薄膜,经750℃退火处理30 min后,形成了完整的钙钛矿相;与Si衬底相比,在Pt衬底上制备的BST薄膜晶粒更均匀、表面平整无裂纹。在室温、频率为100 kHz条件下薄膜的介电常数ε=353.8,介电损耗tanδ=0.012 8。介电温谱结果表明制备的(Ba0.65Sr0.35)TiO3铁电薄膜居里温度在5.0℃左右。     

倒筒式射频溅射频偏压对Ba0.65Sr0.35TiO3热释电薄膜结构及性能的影响

采用倒筒式射频溅射方法,在Pt、Ti/SiO2/Si基片上制备了Ba0.65Sr0.35TiO3(简称BST)薄膜.研究了自偏压对BST薄膜结构及电学性能的影响.在较高自偏压下制备的BST薄膜具有高度的(100)择优取向,且结晶性好,表面平整,耐压能力强.在25℃时薄膜的热释电系数高达6.73×10-7C.cM-2.K-7.研究结果表明,利用倒筒式射频溅射方法适当提高自偏压,可以制备出热释电性能优良的BST薄膜.     

快速退火对Pt/BST/Pt电容器结构和性能的影响

采用脉冲激光沉积(PLD)法在Pt/Ti/SiO2/Si(001)基片上制备了Ba0.6Sr0.4TiO3(BST)薄膜,对Pt/BST/Pt电容器在空气中进行400℃快速退火(RTA)处理,研究了快速退火对Pt/BST/Pt电容器的结构和性能的影响。结果表明:快速退火虽然对BST薄膜的结晶质量影响较小,但却极大改善了Pt/BST/Pt电容器的电学性能。当测试频率为100kHz、直流偏压为0V时,介电损耗从快速退火前的0.07减小到0.03,介电常数和调谐率略有增加。快速退火后负向漏电流过大现象得到了明显抑制,正负向漏电流趋于对称,在300×103V/cm电场强度下,漏电流密度为4.83×10–5A/cm2。     

BST/LSCO异质结构的研究

利用脉冲激光沉积法在STO(001)基片上外延生长了La0.5Sr0.5CoO3(LSCO)导电氧化物薄膜,研究了基片温度对LSCO薄膜结构和电性能的影响,并制备了Ni-Cr/BST/LSCO多层膜结构。XRD谱发现,沉积温度在450~700℃均能得到高度(00 l)取向的LSCO薄膜,LSCO(002)峰的半高峰宽FWHM=0.1°~0.2°;在LSCO薄膜上制备的BST介质膜具有良好的c轴取向和较高的表面平整度,其εr约为470,tgδ为0.036~0.060。     

应用于DRAM的BST薄膜制备与性能研究

BaxSr1-xTiO3(BST)是动态随机存取存储器(DRAM)中常规电容介质SiO2的替代材料。用溶胶-凝胶(Sol-Gel)法在Si及Pt/Ti/SiO2/Si基片上制备出了较高品质的BST薄膜。系统地研究了在不同退火条件下薄膜的结晶情况、微结构和电学性能。在室温100kHz下,薄膜的介电常数为230。在3V的偏压下,薄膜的漏电流密度为1.6×10-7A/cm2。利用HCl/HF刻蚀溶液成功获得了分辨率达到微米量级的BST薄膜微图形。     

温度对飞秒激光沉积ZnO/Si薄膜的结构和性能的影响

通过飞秒脉冲激光(50 fs,800 nm,1 kHz,2 mJ)沉积技术在n型Si(100)单晶基片上制备了ZnO薄膜.详细研究了基片温度变化以及退火处理对ZnO薄膜的结构、表面形貌及光学性质的影响.X射线衍射(XRD)结果表明,不同温度下(20~350℃)生长的ZnO薄膜具有纤锌矿结构,并且呈c轴择优取向;当基片温度为80℃时,薄膜沿(002)晶面高度择优生长;当基片温度为500℃时薄膜沿(103)晶面择优生长,场发射扫描电子显微镜(FEEM)结果表明薄膜呈纳米晶结构,并观察到了ZnO的六方结构.进一步通过透射光谱的测量讨论了基片温度及退火处理对ZnO薄膜光学透射率的影响,结果表明退火后薄膜的透射率增大.     

氧气氛退火对BST薄膜电阻热敏特性的影响

利用氩离子束镀膜技术在 SiO2/Si 衬底上淀积 BST 薄膜,研究了氧气氛下退火对 BST 薄膜热敏特性的影响。结果表明,当退火温度不太高时(≤600℃),薄膜热敏特性随退火温度升高而变差;但当退火温度较高时(>600℃),薄膜热敏特性随退火温度升高而得到改善。在室温至 200℃范围内 BST 薄膜具有较好的热敏特性,其温度系数最大值为–5.3 %℃–1。并利用 SEM 和 AES 分析了退火条件对薄膜电阻热敏特性的影响机理。     

退火温度对ZnO/PZT薄膜结构及电阻率的影响

采用射频反应磁控溅射法在Pb(Zr0.52Ti0.48)O3(PZT)/Pt/Ti/SiO2/Si基片上制备了ZnO薄膜,利用X线衍射仪(XRD)、原子力显微镜(AFM)、霍尔效应测试系统等对不同退火温度下制备薄膜的结构、形貌及电阻率等进行了分析表征。结果表明,退火温度600℃的ZnO薄膜(002)择优取向较好,晶粒大小均匀,表面平整致密。随着退火温度的增大,电阻率先下降后升高,600℃时ZnO薄膜电阻率达最小。     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Nanoimprint Lithography -A Next Generation High Volume Lithography Technique

IntroductionNanoimprint Lithography is a well-acknowl-edged low cost, high resolution, large area pattern-ing process. It includes the most promising methods,high-pressure hot embossing lithography (HEL) [2],UV-cured imprinting (UV-NIL) [3] and micro contactprinting (m-CP, MCP) [4]. Curing of the imprintedstructures is either done by subsequent UV-lightexposure in the case of UV-NIL or by cooling downbelow the glass transition temperature of the ther-moplastic material in case of HEL…     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

Influence of PVK ： NPB hole transporting layer on the characteristics of organic light-emitting devices

A doping system consisting of NPB and PVK is employed as a composite hole transporting layer （CHTL）. By adjusting the component ratio of the doping system, a series of devices with different concentration proportion of PVK ： NPB are constracted. The result shows that doping concentration of NPB enhances the competence of hole transporting ability, and modifies the recombination region of charge as well as affects the surface morphology of doped film. Optimum device with a maximum brightness of 7852 cd/m^2 and a power efficiency of 1.75 lm/W has been obtained by choosing a concentration proportion of PVK ： NPB at 1：3.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.     

Analysis of error performance on Turbo coded FDPIM

Due to variable symbol length of digital pulse interval modulation（DPIM）, it is difficult to analyze the error performances of Turbo coded DPIM. To solve this problem, a fixed-length digital pulse interval modulation（FDPIM） method is provided. The FDPIM modulation structure is introduced. The packet error rates of uncoded FDPIM are analyzed and compared with that of DPIM. Bit error rates of Turbo coded FDPIM are simulated based on three kinds of analytical models under weak turbulence channel. The results show that packet error rate of uncoded FDPIM is inferior to that of uncoded DPIM. However, FDPIM is easy to be implemented and easy to be combined, with Turbo code for soft-decision because of its fixed length. Besides, the introduction of Turbo code in this modulation can decrease the average power about 10 dBm, which means that it can improve the error performance of the system effectively.     

A method for calculating the center position of collimated light

It is a key problem to accurately calculate beam spots＇ center of measuring the warp by using a collimated laser. A new method, named double geometrical center method （DGCM）, is put forward for the first time. In this method, a plane wave perpendicularly irradiates an aperture stop, and a charge couple device （CCD） is employed to receive the diffraction-beam spots, then the geometrical centers of the fast and the second diffraction-beam spots are calculated respectively, and their mean value is regarded as the center of datum beam. In face of such adverse instances as laser intension distributing defectively, part of the image being saturated, this method can still work well. What＇s more, this method can detect whether an unacceptable error exits in the courses of image receiving, processing and calculating. The experimental results indicate the precision of this method is high.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.