Novel ultrahigh-density flash memory with a stacked-surrounding gate transistor (S-SGT) structured cell

In order to overcome the limitation of cell area of 4F/sup 2/ per bit in conventional NAND flash memory cells, stacked-surrounding gate transistor (S-SGT) structured cell is proposed. This newly structured cell achieves a cell area of 4F/sup 2//N per bit, where N is the number of stacked memory cells in one silicon pillar, without using multibit per memory cell technology. The S-SGT structured cell consisting of two stacked memory cells in one silicon pillar achieves a cell area per bit of less than 50% of the smallest reported NAND structured cell. The novel S-SGT structured cells are fabricated by vertical self-aligned processes using a 0.2 /spl mu/m design rule. The S-SGT structured cell can be programmed and erased by uniform injection and uniform emission of Fowler-Nordheim (F-N) tunneling electrons over the whole channel area of the memory cell, respectively, which is the same program and erase mechanism as in conventional NAND structured cell. This high performance S-SGT structured cell is applicable to high-density nonvolatile memories for 16 G/64 G bit Flash memories and beyond.     

A source-line programming scheme for low-voltage operation NANDflash memories

To realize a low-voltage operation NAND flash memory, a new source-line programming scheme has been proposed. This architecture drastically reduces the program disturbance without circuit area, manufacturing cost, program speed, or power consumption overhead. In order to improve the program disturbance characteristics, a high program inhibit voltage is applied to the channel from the source line, as opposed to from the bit line of the conventional scheme. The bit-line swing is decreased to 0.5 V to achieve a lower power consumption. Although the conventional NAND flash memory cannot operate below 2.0 V due to the program disturbance issue, the proposed NAND flash memory shows excellent program disturbance characteristics irrespective of the supply voltage. A very fast programming of 192 μs/page and a very low power operation of 22 mW at 1.4 V can be realized in the proposed scheme     

多通道NAND闪存控制器的硬件实现

本文提出了在一款片上系统(SOC)芯片设计中的多通道NAND闪存控制器实现方案。在对NAND闪存控制器的结构和实现方法的研究上,闪存控制器利用带两个16K字节缓冲器的高效率缓冲管理控制器来管理4个通道,每个通道可以连接4片闪存芯片。控制器内嵌16比特BCH纠错模块,支持AMBAAHB总线与MLC闪存。文中还介绍了行地址计算与快闪存储器存储单元的初始化。结果分析里给出了控制器的仿真波形、功耗分析和综合结果。在一个存储组与一个通道的配置条件下,控制器的实现只需要71K逻辑门。     

3D NAND闪存数据保持力与初始状态依赖性研究

数据保持力是NAND闪存重要的可靠性指标,本文基于用户在使用模式下,通过设计测试方法,研究了电荷捕获型3D NAND闪存初始阈值电压-2V至3V的范围内数据保持力特性.结果表明初始状态为编程态时,可以有效降低NAND闪存高温数据保留后的误码率,特别是随着擦写次数的增加,不同初始状态下电荷捕获型3D NAND闪存数据保持力差异更加明显,结论表明闪存最适宜存放的状态为0-1V,电荷捕获型3D NAND闪存器件应避免长期处于深擦除状态.并基于不同初始状态闪存高温数据保留后的数据保持力特性不同的现象进行了建模和演示,通过设计实验验证,机理解释模型符合实验结果.该研究可为电荷捕获型3D NAND闪存器件的长期存放状态提供理论参考.     

一种用于NAND闪存的奇偶位线块编程补偿算法

为改善数据保持干扰和编程干扰对NAND闪存可靠性的影响,提出了一种新的奇偶位线块编程补偿算法。该算法利用编程干扰效应来补偿由数据保持引起的阈值漂移,修复NAND闪存因数据保持产生的误码,提高了NAND闪存的可靠性。将该算法应用于编程擦除次数为3k次的1x-nm MLC NAND闪存。实验结果表明,在数据保持时间为1年的条件下,与传统奇偶交叉编程算法相比,采用该补偿算法的NAND闪存的误码降低了93%;与读串扰恢复算法相比,采用该补偿算法的NAND闪存的误码下降了38%。     

Program Cache Busy Time Control Method for Reducing Peak Current Consumption of NAND Flash Memory in SSD Applications

In current NAND flash design, one of the most challenging issues is reducing peak current consumption (peak ICC), as it leads to peak power drop, which can cause malfunctions in NAND flash memory. This paper presents an efficient approach for reducing the peak ICC of the cache program in NAND flash memory — namely, a program Cache Busy Time (tPCBSY) control method. The proposed tPCBSY control method is based on the interesting observation that the array program current (ICC2) is mainly decided by the bit‐line bias condition. In the proposed approach, when peak ICC2 becomes larger than a threshold value, which is determined by a cache loop number, cache data cannot be loaded to the cache buffer (CB). On the other hand, when peak ICC2 is smaller than the threshold level, cache data can be loaded to the CB. As a result, the peak ICC of the cache program is reduced by 32% at the least significant bit page and by 15% at the most significant bit page. In addition, the program throughput reaches 20 MB/s in multiplane cache program operation, without restrictions caused by a drop in peak power due to cache program operations in a solid‐state drive.     

A 144-Mb, eight-level NAND flash memory with optimized pulsewidthprogramming

We report a fast-programming, compact sense and latch (SL) circuit to realize an eight-level NAND flash memory. Fast programming is achieved by supplying optimized voltage and pulsewidth to the bit lines, according to the programming data. As a result, all data programming is completed almost simultaneously, and 0.67-MB/s program throughput, which is 1.7 times faster than conventional program throughput, is achieved. The compact layout of the SL circuit is made possible by four 3-bit latches sharing one unit of the read/verify control circuit. Using these techniques, we fabricated a 144-Mb, eight-level NAND flash memory using a 0.35-μm CMOS process, resulting in a 104.2-mm² die size and a 1.05-μm² effective cell size     

Soft-Decision Error Correction of NAND Flash Memory with a Turbo Product Code

As NAND flash memory fabrication technology scales down to 20 nm and below, the raw bit error rate increases very rapidly and conventional hard-decision based error correction does not provide enough protection. The turbo product code (TPC) based error correction with multi-precision output from NAND flash memory is promising because of high error-correcting performance and flexibility in code construction. In this work, we construct a rate-0.907 (36116, 32768) extended TPC for 2-bit MLC NAND flash memory, and apply the Chase–Pyndiah decoding algorithm. An efficient complexity reduction scheme is also proposed to eliminate redundant computations in the Chase–Pyndiah decoding algorithm. The replica parallel decoding is also employed to lower the error floor. The experimental results that include the effects of flash memory output precision are presented for a simulated flash memory channel.     

A dual-page programming scheme for high-speed multigigabit-scaleNAND flash memories

To realize a low-cost and high-speed programming NAND flash memory, a new programming scheme, a “dual-page programming scheme,” has been proposed. This architecture drastically increases the program throughput without circuit area overhead. In the proposed scheme, two memory cells are programmed at the same time using only one page buffer. Therefore, the page size, i.e., the number of memory cells programmed simultaneously, is doubled and the program speed is improved. As the number of page buffers required in the proposed scheme is the same as that in the conventional one, there is no circuit area increase. This novel operation is made possible by using a bitline as a dynamic latch to temporarily store the program data. As a result, the programming is accelerated by 73% in a 1-Gb generation and 62% in a 4-Gb generation, 18.2-MB/s 1-Gb or 30.7-MB/s 4-Gb NAND flash memory can be realized with this new architecture     

A 34 MB/s MLC Write Throughput 16 Gb NAND With All Bit Line Architecture on 56 nm Technology

A 16 Gb 4-state MLC NAND flash memory augments the sustained program throughput to 34 MB/s by fully exercising all the available cells along a selected word line and by using additional performance enhancement modes. The same chip operating as an 8 Gb SLC device guarantees over 60 MB/s programming throughput. The newly introduced all bit line (ABL) architecture has multiple advantages when higher performance is targeted and it was made possible by adopting the ldquocurrent sensingrdquo (as opposed to the mainstream ldquovoltage sensingrdquo) technique. The general chip architecture is presented in contrast to a state of the art conventional circuit and a double size data buffer is found to be necessary for the maximum parallelism attained. Further conceptual changes designed to counterbalance the area increase are presented, hierarchical column architecture being of foremost importance. Optimization of other circuits, such as the charge pump, is another example. Fast data access rate is essential, and ways of boosting it are described, including a new redundancy scheme. ABL contribution to energy saving is also acknowledged.     

High‐Performance Top‐Gated Organic Field‐Effect Transistor Memory using Electrets for Monolithic Printed Flexible NAND Flash Memory

High‐performance top‐gated organic field‐effect transistor (OFET) memory devices using electrets and their applications to flexible printed organic NAND flash are reported. The OFETs based on an inkjet‐printed p‐type polymer semiconductor with efficiently chargeable dielectric poly(2‐vinylnaphthalene) (PVN) and high‐k blocking gate dielectric poly(vinylidenefluoride‐trifluoroethylene) (P(VDF‐TrFE)) shows excellent non‐volatile memory characteristics. The superior memory characteristics originate mainly from reversible charge trapping and detrapping in the PVN electret layer efficiently in low‐k/high‐k bilayered dielectrics. A strategy is devised for the successful development of monolithically inkjet‐printed flexible organic NAND flash memory through the proper selection of the polymer electrets (PVN or PS), where PVN/‐ and PS/P(VDF‐TrFE) devices are used as non‐volatile memory cells and ground‐ and bit‐line select transistors, respectively. Electrical simulations reveal that the flexible printed organic NAND flash can be possible to program, read, and erase all memory cells in the memory array repeatedly without affecting the non‐selected memory cells.     

6G移动网络中闪存系统的性能优化方案:比特重映射

第6代移动通信技术(6G)网络所产生的海量数据对数据存储带来了全新挑战,推动着存储技术的迅猛发展。与非门(NAND)闪存存储器具有读写速度快,可靠性高等优点,故在6G网络中具有广泛的应用前景。为了提高NAND闪存的可靠性,针对两种不同位线结构的错误特性,该文分别提出基于全位线结构的等精度重映射方案和基于奇偶位线结构的不等精度的重映射方案。仿真结果表明,两种新型比特重映射方案有效提升了闪存的误码性能。基于此,该文所提重映射技术可被视作6G网络中可靠而高效的存储优化技术。     

A side-wall transfer-transistor cell (SWATT cell) for highlyreliable multi-level NAND EEPROMs

A multi-level NAND Flash memory cell, using a new Side-WAll Transfer-Transistor (SWATT) structure, has been developed for a high performance and low bit cost Flash EEPROM. With the SWATT cell, a relatively wide threshold voltage (V_th) distribution of about 1.1 V is sufficient for a 4-level memory cell in contrast to a narrow 0.6 V distribution that is required for a conventional 4-level NAND cell. The key technology that allows this wide V_th distribution is the Transfer Transistor which is located at the side wall of the Shallow Trench Isolation (STI) region and is connected in parallel with the floating gate transistor. During read, the Transfer Transistors of the unselected cells (connected in series with the selected cell) function as pass transistors. So, even if the V_th of the unselected floating gate transistor is higher than the control gate voltage, the unselected cell will be in the ON state. As a result, the V_th distribution of the floating gate transistor can be wider and the programming can be faster because the number of program/verify cycles can be reduced. Furthermore, the SWATT cell results in a very small cell size of 0.57 μm² for a 0.35 μm rule. Thus, the SWATT cell combines a small cell size with a multi-level scheme to realize a very low bit cost. This paper describes the process technology and the device performance of the SWATT cell, which can be used to realize NAND EEPROM's of 512 Mbit and beyond     

适于空间图像闪存阵列的非与闪存控制器

提出一种适于空间应用的非与(NAND,not and)闪存控制器。首先,分析了空间相机存储图像的要求,说明了闪存控制器结构的特点。接着,分析了闪存数据存储差错的机理,针对闪存结构组织特点提出了一种基于BCH(Bose-Chaudhuri-Hocquenghem,2108,2048,5)码的闪存纠错算法。然后,对传统BCH编码器进行了改进,提出了一种8bit并行蝶形阵列处理机制。最后,使用地面检测设备对闪存控制器进行了试验验证。结果表明,闪存控制器能快速稳定、可靠地工作,在闪存单页2Kbt/page下可以纠正40bit错误,在相机正常工作行频为2.5kHz下拍摄图像时4级流水线闪存连续写入速度达到133Mbit/s,可以满足空间相机图像存储系统的应用。     

A 130-mm2, 256-Mbit NAND flash with shallow trenchisolation technology

A 256-Mbit flash memory has been developed using a NAND cell structure with a shallow trench isolation (STI) process. A tight bit-line pitch of 0.55 μm is achieved with 0.25-μm STI. The memory cell is shrunk to 0.29 μm², which realizes a 130-mm² , 256-Mbit flash memory. Peripheral transistors are scaled with memory cells in order to reduce fabrication process steps. A voltage down converter, which generates 2.5-V constant internal power source, is applied to protect the scaled transistors. An improved bit-line clamp sensing scheme achieves 3.8-μs first access time in spite of long and tight pitch bit-line. A 1-kbyte page mode with 35-ns serial data out realizes 25-Mbyte/s read throughput. An incremental step pulse with a bit by bit verify scheme programs 1-k cells in 1-V Vt distribution within 200 μs. That realizes 4.4-Mbyte/s programming throughput     

Reliability issues of flash memory cells

Reliability issues for flash electrically erasable programmable read-only memories are reviewed. The reliability of both the source-erase type (ETOX) flash memory and the NAND structure EEPROM are discussed. Disturbs during programming, write/erase endurance, charge loss of both devices are reviewed, and the reliability of the tunnel oxide and the interpoly dielectric are described. It is shown that bipolarity F-N programming/erase, which is used in the NAND EEPROM, improves the charge to breakdown and decreases the stress-induced leakage current     

Low Voltage Flash Memory Cells Using SiGe Quantum Dots for Enhancing F-N Tunneling

提出了一种用于半导体闪速存储器单元的新的Si/SiGe量子点/隧穿氧化层/多晶硅栅多层结构,该结构可以实现增强F-N隧穿的编程和擦除机制.模拟结果表明该结构具有高速和高可靠性的优点.测试结果表明该结构的工作电压比传统NAND结构的存储器单元降低了4V.采用该结构能够实现高速、低功耗和高可靠性的半导体闪速存储器.     

基于SiGe量子点实现增强F-N隧穿的低压闪速存储器

提出了一种用于半导体闪速存储器单元的新的Si/SiGe量子点/隧穿氧化层/多晶硅栅多层结构,该结构可以实现增强F-N隧穿的编程和擦除机制.模拟结果表明该结构具有高速和高可靠性的优点.测试结果表明该结构的工作电压比传统NAND结构的存储器单元降低了4V.采用该结构能够实现高速、低功耗和高可靠性的半导体闪速存储器.     

A PWM analog memory programming circuit for floating-gate MOSFETswith 75-μs programming time and 11-bit updating resolution

This paper describes a programming circuit for analog memory using pulsewidth modulation (PWM) signals and the circuit performance obtained from measurements using a floating-gate EEPROM device. This programming circuit attains both high programming speed and high precision. We fabricated the programming circuit using standard 0.6-μm CMOS technology and constructed an analog memory using the programming circuit and a floating-gate MOSFET. The measurement results indicate that the analog memory attains a programming time of 75 μs, an updating resolution of 11 bit, and a memory setting precision of 6.5 bit. This programming circuit can be used for intelligent information processing hardware such as self-learning VLSI neural networks as well as multilevel flash memory     

A 16 Gb 3-Bit Per Cell (X3) NAND Flash Memory on 56 nm Technology With 8 MB/s Write Rate

A 16 Gb 8-level NAND flash chip on 56 nm CMOS technology has been fabricated and is being reported for the first time. This is the first 3-bit per cell (X3) chip published with all-bitline (ABL) architecture, which doubles the write performance compared with conventional shielded bitline architecture. A new advanced cache program algorithm provides another 15% improvement in write performance. This paper also discusses a technique for resolving the sensing error resulting from cell source line noise, which usually varies with the data pattern. The new architecture and advanced algorithm enable an 8 MB/s write performance that is comparable to previously published 2-bit per cell (4-level) NAND performance. Considering the significant cost reduction compared to 4-level NAND flash based on the same technology, this chip is a strong candidate for many mainstream applications.