击穿电压提高的AlGaN/GaN/AlGaN双异质结特性

本文论述了AlGaN/GaN双异质结高电子迁移率晶体管的特性,该结构使用Al组分为7%的AlGaN来代替传统的GaN作为缓冲层。Al0.07Ga0.93N缓冲层增加了二维电子气沟道下方的背势垒高度,有效提高了载流子限阈性,从而造成缓冲层漏电的显著减小以及击穿电压的明显提高。对于栅尺寸为0.5100μm,栅漏间距为1μm的器件,AlGaN/GaN 双异质结器件的击穿电压（~100V）是常规单异质结器件的两倍（~50V）。本文中的双异质结器件在漏压为35V、频率为4GHz下,最大输出功率为7.78W/mm,最大功率附加效率为62.3%,线性增益为23dB。     

X波段GaN HEMT内匹配器件

自主研制的GaN HEMT,栅源泄漏电流从10-4 A量级减小到了10 -6 A量级,有效提高了栅漏击穿电压,改善了器件工作特性.采用MIS结构制作了2.5mm栅宽GaN HEMT,测试频率为8GHz,漏源电压为33V时,器件连续波输出功率为18.2W,功率增益为7.6dB,峰值功率附加效率为43.0%.2.5mm×4 GaN HEMT内配配器件,测试频率8GHz,连续波输出功率64.5W,功率增益7.2dB,功率附加效率39%.     

X波段GaN HEMT内匹配器件

自主研制的GaN HEMT,栅源泄漏电流从1E-4A量级减小到了1E-6A量级,有效提高了栅漏击穿电压,改善了器件工作特性. 采用MIS结构制作了2.5mm栅宽GaN HEMT,测试频率为8GHz,漏源电压为33V时,器件连续波输出功率为18.2W,功率增益为7.6dB,峰值功率附加效率为43.0%. 2.5mm×4 GaN HEMT内匹配器件,测试频率8GHz,连续波输出功率64.5W,功率增益7.2dB,功率附加效率39%.     

具有高击穿电压的AlN背势垒AlGaN/GaN/AlN HEMT材料

采用金属有机化学气相沉积(MOCVD)技术在4英寸(1英寸=2.54 cm)蓝宝石衬底上制备了1.2μm厚的AlN背势垒的AlGaN/GaN/AlN双异质结高电子迁移率晶体管(HEMT)材料,其AlGaN势垒层表面粗糙度(RMS)、二维电子气(2DEG)迁移率以及HEMT材料的弯曲度都较为接近于常规的高阻GaN背势垒结构的HEMT材料。由于AlN晶格常数较小,具有AlN背势垒的HEMT材料受到了更大的压应力。通过对比分析两种HEMT材料所制备的器件发现,受益于AlN背势垒层更高的禁带宽度和临界电场,由AlN背势垒HEMT材料所制备的器件三端关态击穿电压为常规高阻GaN背势垒HEMT器件的1.5倍,缓冲层漏电流则较常规高阻GaN背势垒HEMT器件低2～3个数量级。     

0.15μm GaN HEMT及其应用

报道了毫米波应用的0.15μm场板结构GaN HEMT。器件研制采用了76.2mm(3英寸)SiC衬底上外延生长的AlGaN/GaN异质结构材料,该材料由MOCVD技术生长并引入了掺Fe GaN缓冲层技术以提升器件击穿电压。器件栅脚和集成了场板的栅帽均由电子束光刻实现,并采用栅挖槽技术来控制器件夹断电压。研制的2×75μm栅宽GaN HEMT在24V工作电压、35GHz频率下的负载牵引测试结果显示其输出功率密度达到了4W/mm,对应的功率增益和功率附加效率分别为5dB和35%。采用该0.15μm GaN HEMT技术进行了Ka波段GaN功率MMIC的研制,所研制的功率MMIC在24V工作电压下脉冲工作时(100μs脉宽、10%占空比),29GHz频点处饱和功率达到了10.64W。     

非掺杂AlGaN/GaN微波功率HEMT

报道了研制的AlGaN/GaN微波功率HEMT,该器件采用以蓝宝石为衬底的非掺杂AlGaN/GaN异质结构,器件工艺采用了Ti/Al/Ni/Au欧姆接触和Ni/Au肖特基势垒接触以及SiN介质进行器件的钝化.研制的200μm栅宽T型布局AlGaN/GaN HEMT在1.8GHz,Vds=30V时输出功率为28.93dBm,输出功率密度达到3.9W/mm,功率增益为15.59dB,功率附加效率(PAE)为48.3%.在6.2GHz,Vds=25V时该器件输出功率为27.06dBm,输出功率密度为2.5W/mm,功率增益为10.24dB,PAE为35.2%.     

高性能1mm SiC基AlGaN/GaN功率HEMT研制

在6H-SiC衬底上,外延生长了AlGaN/GaN HEMT结构,设计并实现了高性能1mm AlGaN/GaN微波功率HEMT,外延材料利用金属有机物化学气相淀积技术生长.测试表明,该lmm栅宽器件栅长为0.8μm,输出电流密度达到1.16A/mm,跨导为241mS/mm,击穿电压＞80V,特征频率达到20GHz,最大振荡频率为28GHz.5.4GHz连续波测试下功率增益为14.2dB,输出功率达4.1W,脉冲条件测试下功率增益为14.4dB,输出功率为5.2W,两端口阻抗特性显示了在微波应用中的良好潜力.     

X波段GaN千瓦级功率放大器的设计

为满足新型雷达对千瓦级大功率放大器的需求,采用0.25μm GaN HEMT工艺研制了一款输出功率大于2 000 W的X波段内匹配功率放大器。通过背势垒层结构与双场板结构提高器件击穿电压,使GaN HEMT管芯的工作电压达到60 V。通过负载牵引得到管芯最优阻抗,采用T型匹配网络和功率分配/合成器将管芯阻抗匹配到50Ω。在工作电压60 V、占空比1‰、脉宽5μs测试条件下,9.0～9.4 GHz频段内输出功率大于2 000 W,最大功率密度达到10.4 W/mm,功率增益大于7 dB,功率附加效率大于37.2%。     

高性能1mm SiC基AlGaN/GaN功率HEMT研制

在6H-SiC衬底上,外延生长了AlGaN/GaN HEMT结构,设计并实现了高性能1mm AlGaN/GaN微波功率HEMT,外延材料利用金属有机物化学气相淀积技术生长.测试表明,该lmm栅宽器件栅长为0.8μm,输出电流密度达到1.16A/mm,跨导为241mS/mm,击穿电压＞80V,特征频率达到20GHz,最大振荡频率为28GHz.5.4GHz连续波测试下功率增益为14.2dB,输出功率达4.1W,脉冲条件测试下功率增益为14.4dB,输出功率为5.2W,两端口阻抗特性显示了在微波应用中的良好潜力.     

P波段超大功率50V GaN HEMT

报道了0.5μm工艺千瓦级GaN HEMT器件在P波段应用。通过采用AlN插入层,大幅降低了器件在大功率工作时的漏电,同时大幅提高器件输出功率密度。同时通过对背势垒结构缓冲层的优化,提高了器件击穿电压,从而提高器件抗失配比(VSWR)至5∶1。GaN HEMT器件设计采用双场板结构,采用0.5μm栅长工艺制作。器件工作电压为50V,在P波段峰值输出功率1 500 W,漏极效率72%。     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.