A low power high gain gain-controlled LNAC＋mixer for GNSS receivers

A low power high gain gain-controlled LNAC+mixer for GNSS receivers is reported. The high gain LNA is realized with a current source load.Its gain-controlled ability is achieved using a programmable bias circuit. Taking advantage of the high gain LNA, a high noise figure passive mixer is adopted. With the passive mixer, low power consumption and high voltage gain of the LNACmixer are achieved. To fully investigate the performance of this circuit, comparisons between a conventional LNAC+mixer, a previous low power LNAC+mixer, and the proposed LNAC+mixer are presented. The circuit is implemented in 0.18 m mixed-signal CMOS technology. A 3.8 dB noise figure, an overall 45 dB converge gain and a 10 dB controlled gain range of the two stages are measured. The chip occupies 0.24 mm2and consumes 2 mA current under 1.8 V supply.     

A 5 GHz 7.2 dB NF low power direct conversion receiver front-end with balun LNA

A 5GHz low power direct conversion receiver radio frequency front-end with balun LNA is presented. A hybrid common gate and common source structure balun LNA is adopted,and the capacitive cross-coupling technique is used to reduce the noise contribution of the common source transistor.To obtain low l/f noise and high linearity,a current mode passive mixer is preferred and realized.A current mode switching scheme can switch between high and low gain modes,and meanwhile it can not only perform good linearity but save power consumption at low gain mode.The front-end chip is manufactured on a 0.13-μm CMOS process and occupies an active chip area of 1.2 mm~2.It achieves 35 dB conversion gain across 4.9-5.1 GHz,a noise figure of 7.2 dB and an IIP3 of -16.8 dBm,while consuming 28.4 mA from a 1.2 V power supply at high gain mode.Its conversion gain is 13 dB with an IIP3 of 5.2 dBm and consumes 21.5 mA at low gain mode.     

A 0.18μm CMOS gain-switched LNA and mixer with large dynamic range

A 2.4GHz 0.18μm CMOS gain-switched single-end Low Noise Amplifier （LNA） and a passive mixer with no external balun for near-zero-IF （Intermediate Frequency）/RF （Radio Frequency） applications are described. The LNA, fabricated in the 0.18μm 1P6M CMOS technology, adopts a gain-switched technique to increase the linearity and enlarge the dynamic range. The mixer is an IQ-based passive topology. Measurements of the CMOS chip are performed on the FR-4 PCB and the input is matched to 50Ω. Combining LNA and mixer, the front-end measured performances in high gain state are： -15dB of Sll, 18.5dB of voltage gain, 4.6dB of noise figure, 15dBm of IIP3, 85dBm to -10dBm dynamic range. The full circuit drains 6mA from a 1.8V supply.     

采用balun低噪声放大器的5GHz 7.2-dB NF低功耗直接转换接收机前端电路

A 5GHz low power direct conversion receiver radio frequency front-end with balun LNA is presented. A hybrid common gate and common source structure balun LNA is adopted, and the capacitive cross-coupling technique is used to reduce the noise contribution of the common source transistor. To obtain low 1/f noise and high linearity, a current mode passive mixer is preferred and realized. A current mode switching scheme can switch between high and low gain modes, and meanwhile it can not only perform good linearity but save power consumption at low gain mode. The front-end chip is manufactured on a 0.13-μm CMOS process and occupies an active chip area of 1.2 mm². It achieves 35 dB conversion gain across 4.9-5.1 GHz, a noise figure of 7.2 dB and an IIP3 of -16.8 dBm, while consuming 28.4 mA from a 1.2 V power supply at high gain mode. Its conversion gain is 13 dB with an IIP3 of 5.2 dBm and consumes 21.5 mA at low gain mode.     

应用于2.4GHz无线传感网的超低功耗射频接收前端设计

This paper presents the design of an ultralow power receiver front-end designed for a wireless sensor network （WSN） in a 0.18 μm CMOS process. The author designs two front-ends working in the saturation region and the subthreshold region respectively. The front-ends contain a two-stage cross-coupling cascaded common-gate （CG） LNA and a quadrature Gilbert IQ mixer. The measured conversion gain is variable with high gain at 24 dB and low gain at 7 dB for the saturation one, and high gain at 22 dB and low gain at 5 dB for the subthreshold one. The noise figure （NF） at high gain mode is 5.1 dB and 6.3 dB for each. The input 1 dB compression point （IPldB） at low gain mode is about -6 dBm and -3 dBm for each. The front-ends consume about 2.1 mA current from 1.8 V power supply for the saturation one and 1.3 mA current for the subthreshold one. The measured results show that, comparing with the power consumption saving, it is worth making sacrifices on the performance for using the subthreshold technology.     

用于U波段移动数字电视的宽带大动态范围高线性度射频前端

A wideband large dynamic range and high linearity U-band RF front-end for mobile DTV is introduced,and includes a noise-cancelling low-noise amplifier(LNA),an RF programmable gain amplifier(RFPGA) and a current communicating passive mixer.The noise/distortion cancelling structure and RC post-distortion compensation are employed to improve the linearity of the LNA.An RFPGA with five stages provides large dynamic range and fine gain resolution.A simple resistor voltage network in the passive mixer decreases the gate bias voltage of the mixing transistor,and optimum linearity and symmetrical mixing is obtained at the same time.The RF front-end is implemented in a 0.25 μm CMOS process.Tests show that it achieves an ⅡP3(third-order intercept point) of –17 dBm,a conversion gain of 39 dB,and a noise figure of 5.8 dB.The RFPGA achieves a dynamic range of –36.2 to 23.5 dB with a resolution of 0.32 dB.     

Radio Frequency Low Noise Amplifier with Linearizing Bias Circuit

A 1.34 GHz-1=60 MHz low noise amplifier （LNA） designed in a 0.35 pm SiGe process is presented. The designed LNA exhibits a power gain of 21.46 dB and a noise figure （NF） of 1.27 dB at 1.34 GHz. The linearity is improved with an active biasing technique. The post-layout simulation shows an input referred 1-dB compression point （IPldn） of-11.52 dBm. Compared with the recent reported high gain LNAs, the proposed LNA has a much better linearity without degrading other performance. The LNA draws 10 mA current from a 3.3 V power supply.     

A RF receiver frontend for SC-UWB in a 0.18-μm CMOS process

正A radio frequency(RF) receiver frontend for single-carrier ultra-wideband(SC-UWB) is presented. The front end employs direct-conversion architecture,and consists of a differential low noise amplifier(LNA),a quadrature mixer,and two intermediate frequency(IF) amplifiers.The proposed LNA employs source inductively degenerated topology.First,the expression of input impedance matching bandwidth in terms of gate-source capacitance, resonant frequency and target S_(11) is given.Then,a noise figure optimization strategy under gain and power constraints is proposed,with consideration of the integrated gate inductor,the bond-wire inductance,and its variation.The LNA utilizes two stages with different resonant frequencies to acquire flat gain over the 7.1-8.1 GHz frequency band,and has two gain modes to obtain a higher receiver dynamic range.The mixer uses a double balanced Gilbert structure.The front end is fabricated in a TSMC 0.18-/im RF CMOS process and occupies an area of 1.43 mm~2.In high and low gain modes,the measured maximum conversion gain are 42 dB and 22 dB,input 1 dB compression points are -40 dBm and -20 dBm,and S_(11) is better than -18 dB and -14.5 dB.The 3 dB IF bandwidth is more than 500 MHz.The double sideband noise figure is 4.7 dB in high gain mode.The total power consumption is 65 mW from a 1.8 V supply.     

A multi-mode multi-band RF receiver front-end for a TD-SCDMA/LTE/LTE-advanced in 0.18-μm CMOS process

正A fully integrated multi-mode multi-band directed-conversion radio frequency(RF) receiver front-end for a TD-SCDMA/LTE/LTE-advanced is presented.The front-end employs direct-conversion design,and consists of two differential tunable low noise amplifiers(LNA),a quadrature mixer,and two intermediate frequency(IF) amplifiers.The two independent tunable LNAs are used to cover all the four frequency bands,achieving sufficient low noise and high gain performance with low power consumption.Switched capacitor arrays perform a resonant frequency point calibration for the LNAs.The two LNAs are combined at the driver stage of the mixer,which employs a folded double balanced Gilbert structure,and utilizes PMOS transistors as local oscillator(LO) switches to reduce flicker noise.The front-end has three gain modes to obtain a higher dynamic range.Frequency band selection and mode of configuration is realized by an on-chip serial peripheral interface(SPI) module.The frontend is fabricated in a TSMC 0.18-μm RF CMOS process and occupies an area of 1.3 mm~2.The measured doublesideband (DSB) noise figure is below 3.5 dB and the conversion gain is over 43 dB at all of the frequency bands. The total current consumption is 31 mA from a 1.8-V supply.     

Design and optimization of a 2.4 GHz RF front-end with an on-chip balun

A 2.4 GHz low-power,low-noise and highly linear receiver front-end with a low noise amplifier(LNA) and balun optimization is presented.Direct conversion architecture is employed for this front-end.The on-chip balun is designed for single-to-differential conversion between the LNA and the down-conversion mixer,and is optimized for the best noise performance of the front-end.The circuit is implemented with 0.35μm SiGe BiCMOS technology.The front-end has three gain steps for maximization of the input dynamic range.The overall maximum gain is about 36 dB.The double-sideband noise figure is 3.8 dB in high gain mode and the input referred third-order intercept point is 12.5 dBm in low gain mode.The down-conversion mixer has a tunable parallel R-C load at the output and an emitter follower is used as the output stage for testing purposes.The total front-end dissipation is 33 mW under a 2.85 V supply and occupies a 0.66 mm~2 die size.     

用于无采保流水线ADC的高速低功耗低失调动态比较器

A novel fully differential high speed high resolution low offset CMOS dynamic comparator has been implemented in the SMIC 0.18 μm process used for a sample-and-hold amplifier （SHA）-less pipelined analog-to-digital converters （ADC）. Based on the analysis and optimization between delay time and offset, an enhanced reset architecture with transmission gate was introduced to speed up the comparison and reset procedure. Four inputs with two cross coupled differential pairs, reconstituted bias circuit for tail current transistor and common centroid layouts make the comparator more robust against mismatch and process variations. The simulation results demonstrate that the proposed design achieves 1 mV sensitivity at 2.2 GHz sampling rate with a power consumption of 510 μW, while the mean offset voltage is equal to 10.244 mV.     

一种基于低中频接收相位选择发射结构的工作在2.4GHz面向WPAN应用的超低功耗收发机

This paper presents a 2.4 GHz CMOS transceiver for the wireless personal area network （WPAN） inte- grated in 0.18/zm CMOS technology. This transceiver adopts a low-IF receiver, a MUX based transmitter and a fast-setting fractional-N frequency synthesizer. For achieving low cost and low power consumption, an inductor- less receiver front-end, an adaptive analog baseband, a low power MUX and a current-reused phase-locked loop （PLL） have been proposed in this work. Measured results show that the receiver achieves-8 dBrn of lIP3 and 31 dB of image rejection. The transmitter delivers 0 dBm output power at a data rate of 2 Mbps. The current consumption is 7.2 mA in the receiving mode and 6.9 mA in the transmitting mode, respectively.     

一种应用于无线传感器网络的低电压低功耗上混频器

This paper presents an up-conversion mixer for 2.4-2.4835 GHz wireless sensor networks （WSN） in 0.18 μm RF CMOS technology. It was based on a double-balanced Gilbert cell type, with two Gilbert cells having quadrature modulation applied. Current-reuse and cross positive feedback techniques were applied in the mixer to boost conversion gain; the current source stage was removed from the mixer to improve linearity. Measured results exhibited that under a 1 V power supply, the conversion gain was 5 dB, the input referred 1 dB compression point was -11 dBm and the IIP3 was -0.75 dBm, while it only consumed 1.4 mW.     

90nm CMOS工艺低功耗20GHz比较器设计

A low power 20 GHz CMOS dynamic latched regeneration comparator for ultra-high-speed, low-power analog-to-digital converters （ADCs） is proposed. The time constant in both the tracking and regeneration phases of the latch are analyzed based on the small signal model. A dynamic source-common logic （SCL） topology is adopted in the master-slave latch to increase the tracking and regeneration speeds. Implemented in 90 nm CMOS technology, this comparator only occupies a die area of 65 × 150 μm^2 with a power dissipation of 14 mW from a 1.2 V power supply. The measurement results show that the comparator can work up to 20 GHz. Operating with an input frequency of 1 GHz, the circuit can oversample up to 20 Giga-sampling-per-second （GSps） with 5 bits resolution; while operating at Nyquist, the comparator can sample up to 20 GSps with 4 bits resolution. The comparator has been successfully used in a 20 GSps flash ADC and the circuit can be also used in other high speed applications.     

一种应用于无线局域网具有3.01-3.82 GHz频率范围和6.29%调谐增益变化的CMOS LC压控振荡器

A wideband low-phase-noise LC voltage-controlled oscillator （VCO） with low VCO gain （Kvco） vari- ation for WLAN fractional-N frequency synthesizer application is proposed and designed on a 0.13-μm CMOS process. In order to achieve a low Kvco variation, an extra switched varactor array was added to the LC tank with the conventional switched capacitor array. Based on the proposed switched varactor array compensation technique, the measured Kvco is 43 MHz/V with only 6.29% variation across the entire tuning range. The proposed VCO provides a tuning range of 23.7% from 3.01 to 3.82 GHz, while consuming 9 mA of quiescent current from a 2.3 V supply. The VCO shows a low phase noise of-121.94 dBc/Hz at 1 MHz offset, from the 3.6 GHz carrier.     

一种电流复用共栅低噪声放大器的低功耗433/915-MHz射频前端的设计

This paper presents a wideband RF front-end with novel current-reuse wide band low noise amplifier(LNA),current-reuse V –I converter,active double balanced mixer and transimpedance amplifier for short range device(SRD) applications.With the proposed current-reuse LNA,the DC consumption of the front-end reduces considerably while maintaining sufficient performance needed by SRD devices.The RF front-end was fabricated in 0.18 μm RFCMOS process and occupies a silicon area of just 0.11 mm2.Operating in 433 MHz band,the measurement results show the RF front-end achieves a conversion gain of 29.7 dB,a double side band noise figure of 9.7 dB,an input referenced third intercept point of –24.9 dBm with only 1.44 mA power consumption from 1.8 V supply.Compared to other reported front-ends,it has an advantage in power consumption.     

Ranking Potential Reply-Providers in Community Question Answering System

Community Question Answering （CQA） websites have greatly facilitated users＇ lives, with an increasing number of people seeking help and exchanging ideas on the Internet. This newlymerged community features two characteristics： social relations and an ask-reply mechanism. As users＇ behaviours and social statuses play a more important role in CQA services than traditional answer retrieving websites, researchers＇ concerns have shifted from the need to passively find existing answers to actively seeking potential reply providers that may give answers in the near future. We analyse datasets derived from an online CQA system named ＂Quora＂, and observed that compared with traditional question answering services, users tend to contribute replies rather than questions for help in the CQA system. Inspired by the findings, we seek ways to evaluate the users＇ ability to offer prompt and reliable help, taking into account activity, authority and social reputation char- acteristics. We propose a hybrid method that is based on a Question-User network and social network using optimised PageRank algorithm. Experimental results show the efficiency of the proposed method for ranking potential answer-providers.     

一种应用于GNSS接收机的低噪声和低杂散频率综合器

A low phase noise and low spur phase locked loop （PLL） frequency synthesizer for use in global navigation satellite system （GNSS） receivers is proposed. To get a low spur, the symmetrical structure of the phase frequency detector （PFD） produces four control signals, which can reach the charge pump （CP） simultaneously, and an improved CP is realized to minimize the charge sharing and the charge injection and make the current matched. Additionally, the delay is controllable owing to the programmable PFD, so the dead zone of the CP can be eliminated. The output frequency of the VCO can be adjusted continuously and precisely by using a programmable LC-TANK. The phase noise of the VCO is lowered by using appropriate MOS sizes. The proposed PLL frequency synthesizer is fabricated in a 0.18 μm mixed-signal CMOS process. The measured phase noise at 1 MHz offset from the center frequency is -127.65 dBc/Hz and the reference spur is -73.58 dBc.     

一个全差分可编程的多通道神经信号记录芯片

A multi-channel,fully differential programmable chip for neural recording application is presented.The integrated circuit incorporates eight neural recording amplifiers with tunable bandwidth and gain,eight 4thorder Bessel switch capacitor filters,an 8-to-1 analog time-division multiplexer,a fully differential successive approximation register analog-to-digital converter(SAR ADC),and a serial peripheral interface for communication.The neural recording amplifier presents a programmable gain from 53 dB to 68 dB,a tunable low cut-off frequency from 0.1 Hz to 300 Hz,and 3.77 μVrms input-referred noise over a 5 kHz bandwidth.The SAR ADC digitizes signals at maximum sampling rate of 20 kS/s per channel and achieves an ENOB of 7.4.The integrated circuit is designed and fabricated in 0.18-μm CMOS mix-signal process.We successfully performed a multi-channel in-vivo recording experiment from a rat cortex using the neural recording chip.