A 3.1-4.8 GHz CMOS receiver for MB-OFDM UWB

An integrated fully differential ultra-wideband CMOS receiver for 3.1-4.8 GHz MB-OFDM systems is presented. A gain controllable low noise amplifier and a merged quadrature mixer are integrated as the RF front-end. Five order Gm-C type low pass filters and VGAs are also integrated for both I and Q IF paths in the receiver. The ESD protected chip is fabricated in a Jazz 0.18μm RF CMOS process and achieves a maximum total voltage gain of 65 dB, an AGC range of 45 dB with about 6 dB/step, an averaged total noise figure of 6.4 to 8.8 dB over 3 bands and an in-band IIP3 of-5.1 dBm. The receiver occupies 2.3 mm2 and consumes 110 mA from a 1.8 V supply including test buffers and a digital module.     

一种应用于WiMAX协议的全集成3.5GHzCMOS功率驱动放大器

A fully integrated CMOS differential power amplifier driver(PAD) is proposed for WiMAX applications. In order to fulfill the differential application requirements,a transmission line transformer is used as the output matching network.A differential inductance constitutes an inter-stage matching network.Meanwhile,an on chip balun realizes input matching as well as single-end to differential conversion.The PAD is fabricated in a 0.13μm RFCMOS process.The chip size is 1.1×1.1 mm~2 with all of the matching network integrated on chip. The saturated power is around 10 dBm and power gain is about 12 dB.     

一种集成二进制权精确对数线性可编程增益放大器的卫星导航接收机数字自动增益控制环路

A novel digitally controlled automatic gain control(AGC) loop circuitry for the global navigation satellite system(GNSS) receiver chip is presented. The entire AGC loop contains a programmable gain amplifier(PGA),an AGC circuit and an analog-to-digital converter(ADC), which is implemented in a 0.18 m complementary metal–oxide–semiconductor(CMOS) process and measured. A binary-weighted approach is proposed in the PGA to achieve wide d B-linear gain control with small gain error. With binary-weighted cascaded amplifiers for coarse gain control, and parallel binary-weighted trans-conductance amplifier array for fine gain control, the PGA can provide a 64 dB dynamic range from4 to 60 dB in 1.14 dB gain steps with a less than 0.15 dB gain error. Based on the Gaussian noise statistic characteristic of the GNSS signal, a digital AGC circuit is also proposed with low area and fast settling. The feed-backward AGC loop occupies an area of 0.27 mm2 and settles within less than165 s while consuming an average current of 1.92 mA at 1.8 V.     

A multi-channel analog IC for in vitro neural recording

Recent work in the field of neurophysiology has demonstrated that, by observing the firing characteristic of action potentials (AP) and the exchange pattern of signals between neurons, it is possible to reveal the nature of "memory" and "thinking" and help humans to understand how the brain works. To address these needs, we developed a prototype fully integrated circuit (IC) with micro-electrode array (MEA) for neural recording. In this scheme, the microelectrode array is composed by 64 detection electrodes and 2 reference electrodes. The proposed IC consists of 8 recording channels with an area of 5 × 5 mm². Each channel can operate independently to process the neural signal by amplifying, filtering, etc. The chip is fabricated in 0.5-μ m CMOS technology. The simulated and measured results show the system provides an effective device for recording feeble signal such as neural signals.     

A low noise CMOS RF front-end for UWB 6-9 GHz applications

An integrated fully differential ultra-wideband CMOS RF front-end for 6-9 GHz is presented.A resistive feedback low noise amplifier and a gain controllable IQ merged folded quadrature mixer are integrated as the RF front-end. The ESD protected chip is fabricated in a TSMC 0.13μm RF CMOS process and achieves a maximum voltage gain of 23-26 dB and a minimum voltage gain of 16-19 dB,an averaged total noise figure of 3.3-4.6 dB while operating in the high gain mode and an in-band IIP3 of-12.6 dBm while in th...     

A low power high gain gain-controlled LNAC＋mixer for GNSS receivers

A low power high gain gain-controlled LNAC+mixer for GNSS receivers is reported. The high gain LNA is realized with a current source load.Its gain-controlled ability is achieved using a programmable bias circuit. Taking advantage of the high gain LNA, a high noise figure passive mixer is adopted. With the passive mixer, low power consumption and high voltage gain of the LNACmixer are achieved. To fully investigate the performance of this circuit, comparisons between a conventional LNAC+mixer, a previous low power LNAC+mixer, and the proposed LNAC+mixer are presented. The circuit is implemented in 0.18 m mixed-signal CMOS technology. A 3.8 dB noise figure, an overall 45 dB converge gain and a 10 dB controlled gain range of the two stages are measured. The chip occupies 0.24 mm2and consumes 2 mA current under 1.8 V supply.     

Low power high gain gain-controlled LNA and mixer for GNSS receivers Wei Binbin(魏斌斌)1, Jiang Jinguang(江金光)1,2,3*

A low power high gain gain-controlled LNA ＋ mixer for GNSS receivers is reported. The high gain LNA is realized with a current source load. Its gain-controlled ability is achieved using a programmable bias circuit. Taking advantage of the high gain LNA, a high noise figure passive mixer is adopted. With the passive mixer, low power consumption and high voltage gain of the LNA ＋ mixer are achieved. To fully investigate the performance of this circuit, comparisons between a conventional LNA ＋ mixer, a previous low power LNA ＋ mixer, and the proposed LNA ＋ mixer are presented. The circuit is implemented in 0.18 #m mixed-signal CMOS technology. A 3.8 dB noise figure, an overall 45 dB converge gain and a 10 dB controlled gain range of the two stages are measured. The chip occupies 0.24 mm2 and consumes 2 mA current under 1.8 V supply.     

全集成微电子神经桥芯片研究

Nerve tracts interruption is one of the major reasons for dysfunction after spiral cord injury. The microelectronic neural bridge is a method to restore function of interrupted neural pathways, by making use of microelectronic chips to bypass the injured nerve tracts. A low-power fully integrated microelectronic neural bridge chip is designed, using CSMC 0.5-μm CMOS technology. The structure and the key points in the circuit design will be introduced in detail. In order to meet the requirement for implantation, the circuit was modified to avoid the use of off-chip components, and fully monolithic integration is achieved. The operating voltage of the circuit is 4-2.5 V, and the chip area is 1.21×1.18 mm2. According to the characteristic of neural signal, the time-domain method is used in testing. The pass bandwidth of the microelectronic neural bridge system covers the whole frequency range of the neural signal, power consumption is 4.33 mW, and the gain is adjustable. The design goals are achieved.     

Dual-band RF receiver for GPS-L1 and compass-B1 in a 55-nm CMOS

A fully integrated dual-band RF receiver with a low-IF architecture is designed and implemented for GPS-L 1 and Compass-Bl in a 55-nm CMOS process. The receiver incorporates two independent IF channels with 2 or 4 MHz bandwidth to receive dual-band signals around 1.57 GHz respectively. By implementing a flexible frequency plan, the RF front-end and frequency synthesizer are shared for the dual-band operation to save power consumption and chip area, as well as avoiding LO crosstalk. A digital automatic gain control （AGC） loop is utilized to improve the receiver＇s robustness by optimizing the conversion gain of the analog-to-digital converter （ADC）. While drawing about 20 mA per channel from a 1.2 V supply, this RF receiver achieves a minimum noise figure （NF） of about 1.8 dB, an image rejection （IMR） of more than 35 dB, a maximum voltage gain of about 122 dB, a gain dynamic range of 82 dB, and an maximum input-referred 1 dB compression point of about -36.5 dBm with an active die area of 1.5 × 1.4 mm2 for the whole chip.     

一种集成MSM光电探测器的单片标准CMOS全差分光接收机

This paper presents a realization of a silicon-based standard CMOS,fully differential optoelectronic integrated receiver based on a metal–semiconductor–metal light detector（MSM photodetector）.In the optical receiver, two MSM photodetectors are integrated to convert the incident light signal into a pair of fully differential photogenerated currents.The optoelectronic integrated receiver was designed and implemented in a chartered 0.35μm, 3.3 V standard CMOS process.For 850 nm wavelength,it achieves a 1 GHz 3 dB bandwidth due to the MSM photodetector’s low capacitance and high intrinsic bandwidth.In addition,it has a transimpedance gain of 98.75 dBΩ, and an equivalent input integrated referred noise current of 283 nA from 1 Hz up to–3 dB frequency.     

用于U波段移动数字电视的宽带大动态范围高线性度射频前端

A wideband large dynamic range and high linearity U-band RF front-end for mobile DTV is introduced,and includes a noise-cancelling low-noise amplifier(LNA),an RF programmable gain amplifier(RFPGA) and a current communicating passive mixer.The noise/distortion cancelling structure and RC post-distortion compensation are employed to improve the linearity of the LNA.An RFPGA with five stages provides large dynamic range and fine gain resolution.A simple resistor voltage network in the passive mixer decreases the gate bias voltage of the mixing transistor,and optimum linearity and symmetrical mixing is obtained at the same time.The RF front-end is implemented in a 0.25 μm CMOS process.Tests show that it achieves an ⅡP3(third-order intercept point) of –17 dBm,a conversion gain of 39 dB,and a noise figure of 5.8 dB.The RFPGA achieves a dynamic range of –36.2 to 23.5 dB with a resolution of 0.32 dB.     

用于流水线ADC的频率自适应可编程MDAC电路

A programmable high precision multiplying DAC （MDAC） is proposed. The MDAC incorporates a frequency-current converter （FCC） to adjust the power versus sampling rate and a programmable operational am- plifier （POTA） to achieve the tradeoff between resolution and power of the MDAC, which makes the MDAC suitable for a 12 bit SHA-less pipelined ADC. The prototype of the proposed pipelined ADC is implemented in an SMIC CMOS 0.18 μm 1P6M process. Experimental results demonstrate that power of the proposed ADC varies from 15.4 mW （10 MHz） to 63 mW （100 MHz） while maintaining an SNDR of 60.5 to 63 dB at all sampling rates. The differential nonlinearity and integral nonlinearity without any calibration are no more than 2.2/-1 LSB and 1.6/-1.9 LSB, respectively.     

Real-Time Upstream Services Demonstration in Orthogonal Frequency Division Multiplexing- Passive Optical Network System

Abstract： Real-time digital service and mul- timedia service upstream transmission in Dig- ital Signal Processing （DSP）-based Orthogo- nal Frequency Division Multiplexing-Passive Optical Network （OFDM-PON） is experimen- tally demonstrated with Centralised Light Sou- rce （CLS） configuration in this paper. After transmitted over 25 km Standard Single Mode Fibre （SSMF） with -16.5 dBm optical power at receiver, the Bit Error Rate （BER） is 9.5 ×10^-11. The implementations of digital domain up-conversion and down-conversion based on Field Programmable Gate Array （FPGA） are int- roduced, which can reduce the cost of In-ph- ase and Quadrature （IQ） radio frequency mix- ers utilised at transmitter and receiver. A car- rier synchronization algorithm is implemented for compensating carrier offset. A channel eq- ualization algorithm is adopted for compen- sating the damage of channel. A new structure of Frequency Synchronization Unit （FSU） des- igned in FPGA is also proposed to cope with the frequency shifting at receiver.     

Ranking Potential Reply-Providers in Community Question Answering System

Community Question Answering （CQA） websites have greatly facilitated users＇ lives, with an increasing number of people seeking help and exchanging ideas on the Internet. This newlymerged community features two characteristics： social relations and an ask-reply mechanism. As users＇ behaviours and social statuses play a more important role in CQA services than traditional answer retrieving websites, researchers＇ concerns have shifted from the need to passively find existing answers to actively seeking potential reply providers that may give answers in the near future. We analyse datasets derived from an online CQA system named ＂Quora＂, and observed that compared with traditional question answering services, users tend to contribute replies rather than questions for help in the CQA system. Inspired by the findings, we seek ways to evaluate the users＇ ability to offer prompt and reliable help, taking into account activity, authority and social reputation char- acteristics. We propose a hybrid method that is based on a Question-User network and social network using optimised PageRank algorithm. Experimental results show the efficiency of the proposed method for ranking potential answer-providers.     

一种应用于GNSS接收机的低噪声和低杂散频率综合器

A low phase noise and low spur phase locked loop （PLL） frequency synthesizer for use in global navigation satellite system （GNSS） receivers is proposed. To get a low spur, the symmetrical structure of the phase frequency detector （PFD） produces four control signals, which can reach the charge pump （CP） simultaneously, and an improved CP is realized to minimize the charge sharing and the charge injection and make the current matched. Additionally, the delay is controllable owing to the programmable PFD, so the dead zone of the CP can be eliminated. The output frequency of the VCO can be adjusted continuously and precisely by using a programmable LC-TANK. The phase noise of the VCO is lowered by using appropriate MOS sizes. The proposed PLL frequency synthesizer is fabricated in a 0.18 μm mixed-signal CMOS process. The measured phase noise at 1 MHz offset from the center frequency is -127.65 dBc/Hz and the reference spur is -73.58 dBc.     

A power-efficient 12-bit analog-to-digital converter with a novel constant-resistance CMOS input sampling switch

Apower-efficient 12-bit40-MS/spipelineanalog-to-digitalconverter（ADC）implementedina0.13 μm CMOS technology is presented. A novel CMOS bootstrapping switch, which offers a constant on-resistance over the entire input signal range, is used at the sample-and-hold front-end to enhance the dynamic performance of the pipelined ADC. By implementing with 2.5-bit-per-stage and a simplified amplifier sharing architecture between two successive pipeline stages, a very competitive power consumption and small die area can be achieved. Meanwhile, the substrate-biasing-effect attenuated T-type switches are introduced to reduce the crosstalk between the two op- amp sharing successive stages. Moreover, a two-stage gain boosted recycling folded cascode （RFC） amplifier with hybrid frequency compensation is developed to further reduce the power consumption and maintain the ADC＇s performance simultaneously. The measured results imply that the ADC achieves a spurious-free dynamic range （SFDR） of 75.7 dB and a signal-to-noise-plus-distortion ratio （SNDR） of 62.74 dB with a 4.3 MHz input signal; the SNDR maintains over 58.25 dB for input signals up to 19.3MHz. The measured differential nonlinearity （DNL） and integral nonlinearity （INL） are -0.43 to ＋0.48 LSB and -1.62 to ＋ 1.89 LSB respectively. The prototype ADC consumes 28.4 mW under a 1.2-V nominal power supply and 40 MHz sampling rate, transferring to a figure- of-merit （FOM） of 0.63 pJ per conversion-step.     

一种应用于GPS接收机的高线性度SiGe HBT低噪声放大器

A high linearity 1.575 GHz SiGe：HBT low noise amplifier （LNA） for global positioning system applications is described. The bipolar cascoded with an MOSFET LNA was fabricated in a commercial 0.18 μm SiGe BiCMOS process, A resistor bias feed circuit with a feedback resistor was designed for the LNA input transistor to improve its intermodulation and compression performance. The packaged chip tested on board has displayed a noise figure of 1. I 1 dB, a power gain of 18 dB, an output 1 dB compression point of ＋7.8 dBm and an input third-order intercept point of ＋1.8 dBm. The chip occupies a 500 × 560μm^2 area and consumes 3.6 mA from a 2.85 V power supply.     

用于无采保流水线ADC的高速低功耗低失调动态比较器

A novel fully differential high speed high resolution low offset CMOS dynamic comparator has been implemented in the SMIC 0.18 μm process used for a sample-and-hold amplifier （SHA）-less pipelined analog-to-digital converters （ADC）. Based on the analysis and optimization between delay time and offset, an enhanced reset architecture with transmission gate was introduced to speed up the comparison and reset procedure. Four inputs with two cross coupled differential pairs, reconstituted bias circuit for tail current transistor and common centroid layouts make the comparator more robust against mismatch and process variations. The simulation results demonstrate that the proposed design achieves 1 mV sensitivity at 2.2 GHz sampling rate with a power consumption of 510 μW, while the mean offset voltage is equal to 10.244 mV.