Low ohmic contact AIN/GaN HEMTs grown by MOCVD

AlN/GaN high-electron-mobility transistors （HEMTs） on SiC substrates were fabricated by metalorganic chemical vapor deposition （MOCVD） and then characterized. An Si/Ti/Al/Ni/Au stack was used to reduce ohmic contact resistance （0.33 g2.mm） at a low annealing temperature. The fabricated devices exhibited a maximum drain current density of 1.07 A/mm （Vows = I V） and a maximum peak extrinsic transconductance of 340 mS/mm. The off-state breakdown voltage of the device was 64 V with a gate-drain distance of 1.9 μm. The current gain extrinsic cutoff frequency fT and the maximum oscillation frequency fmax were 36 and 80 GHz with a 0.25 μm gate length, respectively.     

AlGaN/GaN HEMTs with 0.2μm V-gate recesses for X-band application

正AlGaN/GaN HEMTs with 0.2μm V-gate recesses were developed.The 0.2μm recess lengths were shrunk from the 0.6μm designed gate footprint length after isotropic SiN deposition and anisotropic recessed gate dry etching.The AlGaN/GaN HEMTs with 0.2μm V-gate recesses on sapphire substrates exhibited a current gain cutoff frequency f_t of 35 GHz and a maximum frequency of oscillation f_(max) of 60 GHz.At 10 GHz frequency and 20 V drain bias,the V-gate recess devices exhibited an output power density of 4.44 W/mm with the associated power added efficiency as high as 49%.     

槽栅MOSHEMT研制与特性分析

An A1GaN/GaN recessed-gate MOSHEMT was fabricated on a sapphire substrate. The device, which has a gate length of 1μm and a source-drain distance of 4μm, exhibits a maximum drain current density of 684mA/mrn at Vgs = 4V with an extrinsic transconductance of 219 mS/mm. This is 24.3% higher than the transconductance of conventional A1GaN/GaN HEMTs. The cut-off frequency and the maximum frequency of oscillation are 9.2 GHz and 14.1 GHz, respectively. Furthermore, the gate leakage current is two orders of magnitude lower than for the conventional Schottky contact device.     

F注入AlGaN/GaN增强型HEMT

The fabrication of enhancement-mode AlGaN/GaN HEMTs by fluorine plasma treatment on sapphire substrates is reported. A new method is used to fabricate devices with different fluorine plasma RF power treatments on one wafer to avoid differences between different wafers. The plasma-treated gate regions of devices treated with different fluorine plasma RF powers were separately opened by a step-and-repeat system. The properties of these devices are compared and analyzed. The devices with 150 W fluorine plasma treatment power and with 0.6 μm gate-length exhibited a threshold voltage of 0.57 V, a maximum drain current of 501 mA/mm, a maximum transconductance of 210 mS/mm, a current gain cutoff frequency of 19.4 GHz and a maximum oscillation frequency of 26 GHz. An excessive fluorine plasma treatment power of 250 W results in a small maximum drain current, which can be attributed to the implantation of fluorine plasma in the channel.     

蓝宝石衬底上Ka波段AlN/GaN高电子迁移率晶体管

We report the DC and RF characteristics of AlN/GaN high electron mobility transistors(HEMTs) with the gate length of 100 nm on sapphire substrates. The device exhibits a maximum drain current density of 1.29 A/mm and a peak transconductance of 440 m S/mm. A current gain cutoff frequency and a maximum oscillation frequency of 119 GHz and 155 GHz have been obtained, respectively. Furthermore, the large signal load pull characteristics of the AlN/GaN HEMTs were measured at 29 GHz. An output power density of 429 m W/mm has been demonstrated at a drain bias of 10 V. To the authors’ best knowledge, this is the earliest demonstration of power density at the Ka band for Al N/Ga N HEMTs in the domestic, and also a high frequency of load-pull measurements for Al N/Ga N HEMTs.     

A high-performance enhancement-mode AIGaN/GaN HEMT

An enhancement-mode AlGaN/GaN HEMT with a threshold voltage of 0.35 V was fabricated by fluorine plasma treatment.The enhancement-mode device demonstrates high-performance DC characteristics with a saturation current density of 667 mA/mm at a gate bias of 4 V and a peak transconductance of 201 mS/mm at a gate bias of 0.8 V. The current-gain cut-off frequency and the maximum oscillation frequency of the enhancement-mode device with a gate length of 1μm are 10.3 GHz and 12.5 GHz,respectively,which is compa...     

金刚石 MISFET 器件的研究

Based on the hydrogen-terminated surface channel diamond material,a 1μm gate length diamond metal-insulator-semiconductor field-effect transistor（MISFET） was fabricated.The gate dielectric Al₂O₃ was formed by naturally oxidated thin Al metal layer,and a less than 2 pA gate leakage current was obtained at gate bias between -4 V and 4 V.The DC characteristic of the diamond MISFET showed a drain-current density of 80 mA/mm at drain voltage of -5 V,and a maximum transconductance of 22 mS/mm at gate-source voltage of -3 V.With the small signal measurement,a current gain cutoff frequency of 2.1 GHz was also obtained.     

Fabrication and characterization of high performance AlGaN/GaN HEMTs on sapphire with silicon nitride passivation

AlGaN/GaN high electron mobility transistors(HEMTs)with high performance were fabricated and characterized.A variety of techniques were used to improve device performance,such as AlN interlayer,silicon nitride passivation,high aspect ratio T-shaped gate,low resistance ohmic contact and short drain-source distance. DC and RF performances of as-fabricated HEMTs were characterized by utilizing a semiconductor characterization system and a vector network analyzer,respectively.As-fabricated devices exhibited a maximum drain current density of 1.41 A/mm and a maximum peak extrinsic transconductance of 317 mS/mm.The obtained current density is larger than those reported in the literature to date,implemented with a domestic wafer and processes.Furthermore, a unity current gain cut-off frequency of 74.3 GHz and a maximum oscillation frequency of 112.4 GHz were obtained on a device with an 80 nm gate length.     

Field plated 0.15μm GaN HEMTs for millimeter-wave application

SiN dielectrically-defined 0.15μm field plated GaN HEMTs for millimeter-wave application have been presented.The AlGaN/GaN hetero-structure epitaxial material for HEMTs fabrication was grown on a 3-inch SiC substrate with an Fe doped GaN buffer layer by metal-organic chemical deposition.Electron beam lithography was used to define both the gate footprint and the cap of the gate with an integrated field plate.Gate recessing was performed to control the threshold voltage of the devices.The fabricated GaN HEMTs exhibited a unit current gain cut-off frequency of 39 GHz and a maximum frequency of oscillation of 63 GHz.Load-pull measurements carried out at 35 GHz showed a power density of 4 W/mm with associated power gain and power added efficiency of 5.3 dB and 35%,respectively,for a 0.15 mm gate width device operated at a 24 V drain bias.The developed 0.15μm gate length GaN HEMT technology is suitable for Ka band applications and is ready for millimeter-wave power MMICs development.     

An 88 nm gate-length In_(0.53)Ga_(0.47)As/In_(0.52)Al_(0.48)As InP-based HEMT with f_(max) of 201 GHz

正An 88 nm gate-length In_(0.53)Ga_(0.47)As/In_(0.52)Al_(0.48)As InP-based high electron mobility transistor (HEMT) was successfully fabricated with a gate width of 2×50μm and source-drain space of 2.4μm.The T-gate was defined by electron beam lithography in a trilayer of PMMA/A1/UⅧ.The exposure dose and the development time were optimized,and followed by an appropriate residual resist removal process.These devices also demonstrated excellent DC and RF characteristics:the extrinsic maximum transconductance,the full channel current, the threshold voltage,the current gain cutoff frequency and the maximum oscillation frequency of the HEMTs were 765 mS/mm,591 mA/mm,-0.5 V,150 GHz and 201 GHz,respectively.The HEMTs are promising for use in millimeter-wave integrated circuits.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.     

GaAsSb/InAlAs PA DHBTs Grown by Production MBE

The epi material growth of GaAsSb based DHBTs with InAlAs emitters are investigated using a 4 × 100mm multi-wafer production Riber 49 MBE reactor fully equipped with real-time in-situ sensors including an absorption band edge spectroscope and an optical-based flux monitor. The state-of-the-art hole mobilities are obtained from 100nm thick carbon-doped GaAsSb. A Sb composition variation of less than ± 0.1 atomic percent across a 4 × 100mm platen configuration has been achieved. The large area InAlAs/GaAsSb/InP DHBT device demonstrates excellent DC characteristics,such as BVCEO＞6V and a DC current gain of 45 at 1kA/cm2 for an emitter size of 50μm × 50μm. The devices have a 40nm thick GaAsSb base with p-doping of 4. 5 × 1019cm-3 . Devices with an emitter size of 4μm × 30μm have a current gain variation less than 2% across the fully processed 100mm wafer. ft and fmax are over 50GHz,with a power efficiency of 50% ,which are comparable to standard power GaAs HBT results. These results demonstrate the potential application of GaAsSb/InP DHBT for power amplifiers and the feasibility of multi-wafer MBE for mass production of GaAsSb-based HBTs.     

Noise character analysis and the restraint of self-pulsation laser diodes

We calculate the Langevin noise sources of self-pulsation laser diodes, analyze the effects of active region noise and saturable-absorption region noise on the power fluctuation as well as period fluctuation, and propose a novel method to restrain the noise effects. A visible SIMULINK model is established to simulate the system, The results indicate that the effects of noise in absorption region can be ignored; that with the increase of DC injecting current, the noise effects enhance power jitter, and nevertheless, the period jitter is decreased; and that with external sinusoidal current modulating the self-pulsation laser diode, the noise-induced power jitter and period jitter can be suppressed greatly. This work is valuable for clock recovery in all-optical network.     

High-quality single-crystal CdSe nanoribbons and their optical properties

Large-scale synthesis of single-crystal CdSe nanoribbons is achieved by a modified thermal evaporation method, in which two-step-thermal-evaporation is used to control CdSe sources＇ evaporation. The synthesized CdSe nanoribbons are usually several micrometers in width, 50 nm in thickness, and tens to several hundred micrometers in length. Studies have shown that high-quality CdSe nanoribbons with regular shapes can be obtained by this method. Room-temperature photolumines-cence indicates that the lasing emission at 710 nm has been observed under optical pumping （266 nm） at power densities of 25-153 kW/cm^2. The full width half maximum （FWHM） of the lasing mode is 0.67 nm     

Propagation of hermite-cosh-gaussian beams passing through ABCD optical system with an annular aperture

By using the expansion of the aperture function into a finte sum of complex Gaussian functions, the corresponding analytical expressions of Hermite-cosh-Gaussian beams passing through annular apertured paraxially and symmetrically optical systems written in terms of ABCD matrix were derived, and they could reduce to the cases with squared aperture. In a similar way, the corresponding analytical expressions of cosh-Gaussian beams through annular apertured ABCD matrix were also given. The method could save more calculation time than that by using the diffraction integral formula directly.     

Influence of polarization extinction ratio on distributed polarization coupling detection

Distributed polarization coupling in polarization-maintaining fibers can be detected by using a white light Michelson interferometer. This technique usually requires that only one polarization mode is excited. However, in practical measurement, the injection polarization direction could not be exactly aligned to one of the principal axes of the PMF, so the influence of the polarization extinction ratio should be considered. Based on the polarization coupling theory, the influence of the incident polarization extinction on the measurement result is evaluated and analyzed, and a method for distributed polarization coupling detection is developed when both two orthogonal eigenmodes are excited.     

Call for Papers

正Communications—VLSI Researches and industries of telecommunications have been growing rapidly in the last 20 years and will keep their high growing pace in the next decade.The involved researches and developments cover mobile communications,highway and last-mile broadband communication,domain specific communications,and emerging D2D M2M communications.Radio communication steps into its